To Stop Engine, Operating the Snow Thrower

Figure 6

7.As engine warms up and begins to operate evenly, rotate choke lever slowly to the 1/2 Choke position. When the engine begins to run smoothly, move the choke to the OFF position. If engine falters, return to FULL choke, then slowly move to 1/2 then OFF position.

To Stop Engine

1.To stop engine, turn ignition key counter-clockwise. Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unattended.

To help prevent possible freeze-up of starter, proceed as follows:

1.Run engine for a few minutes before stopping to help dry off any moisture on the engine.

2.Electric Starter: Connect power cord to switch box on engine, then to 120 volt AC receptacle. With the engine running, push starter button and spin the starter for several seconds. The unusual sound made by spinning the starter will not harm engine or starter. Disconnect the power cord from receptacle first, and then from switch box.

3.Recoil Starter: With engine running, pull starter rope with a rapid, continuous full arm stroke three or four times. Pulling the starter rope will produce a loud clattering sound, which is not harmful to the engine or starter.

4.Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times. Leave choke control in the FULL choke position.

5.Remove ignition key and disconnect spark plug wire to prevent accidental starting.

Operating the Snow Thrower

The pitch of the chute assembly controls the angle at which the snow is thrown.

1.Loosen the star knob found on the left side of the chute assembly and

pivot the upper chute upward or downward to the desired pitch.

Retighten the star knob before operating the snow thrower.

2.Position the chute

assembly opening by using the Chute

Handle to throw the snow in the desired direction. See inset Figure 6.

Clearing Snow

WARNING: Never operate the snow thrower with bystanders in front of or near the discharge chute opening.

1.Engage the auger by squeezing the auger control handle against the upper handle. See Figure 5.

2.Lift up slightly on the handle to allow the rubber paddles on the auger to contact the pavement and propel the snow thrower forward. Pushing downward on the handle will raise the augers off the ground and stop forward motion.

3.Discharge snow downwind whenever possible. Slightly overlap each previously cleared path.

NOTE: Excessive upward pressure on the handle will result in premature wear on the rubber auger blades which would not be covered by warranty.

Operating Tips

1.Run the engine for a few minutes before stopping to help dry any moisture on the engine.

2.Clean the snow thrower thoroughly after each use.

WARNING: Muffler, engine and surrounding areas become hot and can cause a burn. Be careful and do not touch when hot.

Operation

WARNING

Muffler, engine and surrounding areas become hot and can cause a burn. Do not touch.

Never operate the snow thrower with bystanders in front of or near the discharge chute opening.

NOTE: Excessive upward pressure on the handle will result in premature wear on the rubber auger blades which would not be covered by warranty.

261, 240, S260, S250, S230 specifications

The MTD S240, S250, S260, and S261 are part of MTD's robust lineup of snow throwers designed to tackle the harsh conditions of winter. Each model is engineered with features and technologies that enhance performance, durability, and ease of use.

The MTD S240 is a compact and lightweight snow thrower, ideal for residential users who need to clear driveways and small walkways. It features a powerful engine that provides reliable performance throughout the winter months. Its 21-inch clearing width and 12-inch intake height allow for efficient snow removal. The S240 is equipped with an adjustable chute that lets users direct the snow exactly where they want, and its manual start makes it straightforward for anyone to operate.

Moving up the range, the MTD S250 provides additional power and features that cater to larger areas. With a wider clearing width of 24 inches, it can handle heavier snowfall with ease. This model is designed with an electric start function, making it convenient for users. The S250 also benefits from advanced traction technology, providing optimal grip and maneuverability on icy surfaces. Its self-propelling feature allows users to navigate effortlessly through snow-ridden paths.

The S260 extends the capabilities even further, incorporating a larger engine that enhances its snow-clearing capabilities. This model boasts a 26-inch clearing width and an impressive intake height, making it suitable for deeper snow conditions. The S260 also includes an LED headlight, which allows for visibility during nighttime snow removal. Its heavy-duty build ensures that it can withstand the rigors of tough winter conditions while reducing maintenance needs.

Lastly, the MTD S261 is a pinnacle model that comes with all the advanced features necessary for professional-grade snow removal. With a larger and more powerful engine, this snow thrower is capable of managing the most challenging snow conditions. Its 27-inch clearing width combined with a high intake height allows it to tackle even the heaviest of snowfalls. The S261 also features an ergonomic design, including heated hand grips and fingertip controls, ensuring comfort for the user during extended operation.

In conclusion, the MTD S240, S250, S260, and S261 models each come equipped with unique features tailored to various snow-clearing needs. From compact residential solutions to powerful options for professional use, MTD provides a snow thrower for every challenge that winter throws your way.