Poulan 436838 To Remove Wheels See Fig, To Adjust Cable Tension See Fig, Carburetor, Engine Speed

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 22

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

TO ADJUST CABLE TENSION (See Fig. 23)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 23

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Exploded KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger HousingScrapper BAR Auger 27 LHSkid Plate LH Auger BearingBearing Plug Skid Plate RHDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketLoop Handle RH Repair Parts Snow Thrower Model XT11530ES HandlesLoop Handle LH Lower TubeTraction ROD 180480Impeller ROD RetainerHandle Knob SpacerKnob RED Washer 3/8Interlock CAM Wire HarnessInterlock Spring Torsion SpringRepair Parts Snow Thrower Model XT11530ES Drive Speed Selector AssemblyDrive Plate Assembly Rubber RingAxle Shaft Sprocket436146X505 Engine ModelFrame Engine Mount Plate428684 Repair Parts Snow Thrower Model XT11530ES Wheels Wheel Assembly LH 432337X428432338X428 Repair Parts Snow Thrower Model XT11530ES BAG of Parts Safety Ignition KEY193071 DECAL, Danger Repair Parts Snow Thrower Model XT11530ES Decals181037 DECAL, DANGER, DeflectorService Notes Service Notes Service Notes Limited Warranty

96192003502, 436838 specifications

The Poulan 436838, also known as the 96192003502, is a powerful and versatile chainsaw designed for both homeowners and professionals. Built to tackle a variety of cutting tasks, this model is a reliable choice for anyone looking to handle yard work or larger outdoor projects.

One of the standout features of the Poulan 436838 is its robust engine. The chainsaw is powered by a high-performing two-stroke engine that provides a balance of power and efficiency. This engine is designed for optimal performance, enabling the chainsaw to handle even the toughest cutting jobs with ease. The power output allows users to cut through hardwoods and dense materials without excessive effort.

In addition to its powerful engine, the Poulan 436838 also boasts an easy-to-use starting system. Equipped with a Prime and Pull starting mechanism, it ensures that users can start the chainsaw with minimal hassle. This feature is particularly beneficial for those who may not be experienced with chainsaws, offering them a straightforward way to get started.

Another significant characteristic of the Poulan 436838 is its lightweight design. Weighing in at just under ten pounds, this chainsaw is manageable for extended periods, reducing user fatigue during operation. The ergonomic handle ensures a comfortable grip, allowing for better control while cutting. This thoughtful design makes it suitable for various users, including those who might not have prior chainsaw experience.

The chainsaw also features an Oregon bar and chain, which enhances its cutting efficiency and durability. The 16-inch bar length provides ample cutting capacity for a wide range of tasks, from pruning branches to felling small trees. The low-kickback design of the chain ensures safer usage, minimizing the risk of accidents while cutting.

Maintenance is made simple with the Poulan 436838, thanks to its tool-less chain tensioning system. Users can easily adjust the chain’s tension without the need for additional tools, allowing for quick and efficient maintenance. This feature ensures that the chainsaw remains in peak operating condition with minimal effort.

In summary, the Poulan 436838,96192003502 is a well-rounded chainsaw that combines power, ease of use, and efficient design. With its impressive features such as a reliable engine, ergonomic design, and convenience-focused maintenance options, it stands out as a practical choice for any cutting task. Whether you’re a seasoned professional or a beginner in yard work, this chainsaw can meet your needs effortlessly.
Top Page Image Contents