Poulan 420915 To Remove Wheels See Fig, Remove the klik pin and remove wheel from axle

Page 17

SERVICE AND ADJUSTMENTS

be replaced. It is recommended that the belt(s) be replaced by a qualified service center.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistantstand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE HAIRPIN FROM CLUTCH ROD and remove clutch rod from swing plate. Tip swing plate forward.

7.REMOVE AUGER BELT from around pulley.

8.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lockwasher and bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

AUGER

SQUARE

BELT

HOLE

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

FIG. 24

TO REMOVE WHEELS (See Fig. 25)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts

17 dealer. Tire sealant also prevents tire dry rot and corrosion.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlEXT RA Shear Bolts and Nuts Rotator Head MountingHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYDeflector remote control lever used to change Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Throw Snow See FigScraper BAR Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Remove the klik pin and remove wheel from axle To Remove Wheels See FigOther StorageTroubleshooting Exploded KEY Part Description Auger Assembly 30 LH Auger HousingAuger Assembly 30 RH Scrapper BARBearing Plug Auger BearingPart Description KEYChute Weldment Deflector Control AssemblyDeflector Weldment Deflector SealCable Assembly LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model PP11530ES Handles Loop Handle RH Loop Handle LHLower Handle Pivot Support WeldmentTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomInterlock Spring Wire HarnessInterlock CAM Torsion SpringDrive Repair PartsRepair Parts Snow Thrower Model PP11530ES Drive END Plate 43 420900 Drive Plate AssemblyWasher Control ARMFrame Tecumseh Engine ModelEngine Mount Plate Belt CoverRepair Parts Snow Thrower Model PP11530ES Wheels 196752X421 Wheel Assembly LH196753X421 Cable Bracket LH35062 Repair Parts Snow Thrower Model PP11530ES BAG of PartsSafety Ignition KEY 181037 Repair Parts Snow Thrower Model PP11530ES DecalsDECAL, Danger DECAL, DANGER, DeflectorService Notes Limited Warranty

420915, 96192001902 specifications

The Poulan 420915, also known as the Poulan Pro 96192001902, is a remarkable outdoor power tool specifically designed for demanding landscaping and yard tasks. This powerful trimmer is well-regarded for its blend of efficiency, durability, and user-friendliness, making it a popular choice among both homeowners and professional landscapers.

One of the standout features of the Poulan 420915 is its effective 28cc 2-stroke engine. This engine delivers reliable power, allowing it to tackle even the toughest overgrowth with ease. The trimmer is designed with a high torque output, which further enhances its cutting efficiency, making it suitable for thick grass and stubborn weeds.

The design of the Poulan 420915 is focused on user comfort and ergonomics. It is equipped with a low-vibration system that minimizes fatigue during extended use, enabling users to work longer without discomfort. Additionally, the trimmer features a lightweight design, making it easy to maneuver and reducing strain on the user’s arms and back.

Another notable characteristic of this trimmer is the easy-to-use start system. The Poulan 420915 incorporates a primer bulb and an automatic choke, simplifying the starting process. This user-friendly technology reduces the likelihood of frustration, allowing users to get to work quickly.

The trimmer is also designed for versatility. With the option to attach various accessories, it can transform into different tools, such as a hedge trimmer or blower. This adaptability makes the Poulan 420915 a multi-functional asset for any landscaping job.

Furthermore, the Poulan 420915 prioritizes ease of maintenance. The air filter can be easily accessed for cleaning and replacement, ensuring the engine remains efficient. The trimmer's design also facilitates quick reloading of the cutting line, minimizing downtime and maximizing productivity.

In terms of cutting capacity, the Poulan 420915 features a dual-line cutting head, which allows for a wider swath and faster trimming. The adjustable cutting width provides the flexibility needed to tackle various landscaping challenges.

In summary, the Poulan 420915,96192001902 is an excellent choice for anyone needing a reliable and efficient trimmer. With its powerful engine, ergonomic design, easy start technology, and versatility, it stands out as a reliable tool for maintaining a beautiful yard. Whether you are a homeowner or a professional, the Poulan 420915 is designed to meet your outdoor needs with ease and effectiveness.
Top Page Image Contents