Poulan 96192001902, 420915 owner manual Storage, Other

Page 18

SERVICE AND ADJUSTMENTS

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

 

AXLE

WHEEL

WHEEL HUB

ENGINE

FIG. 25

 

See engine manual.

 

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents EXT RA Shear Bolts and Nuts Chute Deflector Remote ControlParts Packed Separately in Carton Rotator Head MountingRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Deflector remote control lever used to changeHOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR ADD Gasoline See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Remove the klik pin and remove wheel from axleStorage OtherTroubleshooting Exploded KEY Part Description Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH Scrapper BARAuger Bearing Bearing PlugKEY Part DescriptionDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Rotator Pivot BracketRepair Parts Snow Thrower Model PP11530ES Handles Lower Handle Loop Handle LHLoop Handle RH Pivot Support WeldmentShifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD BottomInterlock CAM Wire HarnessInterlock Spring Torsion SpringRepair Parts DriveRepair Parts Snow Thrower Model PP11530ES Drive Washer 43 420900 Drive Plate AssemblyEND Plate Control ARMEngine Mount Plate Tecumseh Engine ModelFrame Belt CoverRepair Parts Snow Thrower Model PP11530ES Wheels 196753X421 Wheel Assembly LH196752X421 Cable Bracket LHRepair Parts Snow Thrower Model PP11530ES BAG of Parts Safety Ignition KEY35062 DECAL, Danger Repair Parts Snow Thrower Model PP11530ES Decals181037 DECAL, DANGER, DeflectorService Notes Limited Warranty

420915, 96192001902 specifications

The Poulan 420915, also known as the Poulan Pro 96192001902, is a remarkable outdoor power tool specifically designed for demanding landscaping and yard tasks. This powerful trimmer is well-regarded for its blend of efficiency, durability, and user-friendliness, making it a popular choice among both homeowners and professional landscapers.

One of the standout features of the Poulan 420915 is its effective 28cc 2-stroke engine. This engine delivers reliable power, allowing it to tackle even the toughest overgrowth with ease. The trimmer is designed with a high torque output, which further enhances its cutting efficiency, making it suitable for thick grass and stubborn weeds.

The design of the Poulan 420915 is focused on user comfort and ergonomics. It is equipped with a low-vibration system that minimizes fatigue during extended use, enabling users to work longer without discomfort. Additionally, the trimmer features a lightweight design, making it easy to maneuver and reducing strain on the user’s arms and back.

Another notable characteristic of this trimmer is the easy-to-use start system. The Poulan 420915 incorporates a primer bulb and an automatic choke, simplifying the starting process. This user-friendly technology reduces the likelihood of frustration, allowing users to get to work quickly.

The trimmer is also designed for versatility. With the option to attach various accessories, it can transform into different tools, such as a hedge trimmer or blower. This adaptability makes the Poulan 420915 a multi-functional asset for any landscaping job.

Furthermore, the Poulan 420915 prioritizes ease of maintenance. The air filter can be easily accessed for cleaning and replacement, ensuring the engine remains efficient. The trimmer's design also facilitates quick reloading of the cutting line, minimizing downtime and maximizing productivity.

In terms of cutting capacity, the Poulan 420915 features a dual-line cutting head, which allows for a wider swath and faster trimming. The adjustable cutting width provides the flexibility needed to tackle various landscaping challenges.

In summary, the Poulan 420915,96192001902 is an excellent choice for anyone needing a reliable and efficient trimmer. With its powerful engine, ergonomic design, easy start technology, and versatility, it stands out as a reliable tool for maintaining a beautiful yard. Whether you are a homeowner or a professional, the Poulan 420915 is designed to meet your outdoor needs with ease and effectiveness.
Top Page Image Contents