Poulan 96198003101, 435557 owner manual KEY Part Description

Page 23

REPAIR PARTS SNOW THROWER - MODEL PP414EPS30 (96198003101)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART
NO.	NO.	DESCRIPTION

1175321X431 IMPELLER

2427148 GEARBOX ASSEMBLY

3	188909	BEARING
4	427146	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X008 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4-20
10	74780426	SCREW 1/4-20 X .625
11	427942	NUT 5/16-18
12	163183	SCREW 5/16-18 X .625
13	427145	IMPELLER HUB
14	427154	IMPELLER SLEEVE
15	73900600	NUT 3/8-16
16	180355	CARRIAGE BOLT
17	194189	SCREW 13-16 X .625
18	407760	PLUG
19	427302	GEARBOX COVER RH
20	427345	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	427147	IMPELLER SHAFT
30	7836M	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O-RING
35	407767	SCREW 5/16-18 X .750
36	427317	GEARBOX COVER LH
37	192090	SHEAR BOLT

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

23

Image 23

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Exploded KEY Part Description Auger Bearing Auger HousingScrapper BAR CARRIAGEBOLT5/16−18X.625Skid Plate RH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate LHPlastic Washer Weight BARDrift Cutter BAR CARRIAGEBOLT5/16−18X.750Deflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Cable Assembly Heat ShieldRepair Parts Snow Thrower Model PP414EPS30 Handles Pivot Support Weldment Loop Handle LHLoop Handle RH Lower HandleWasher 3/8 SpacerKnob RED Handle KnobCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Sprocket Repair Parts Snow Thrower Model PP414EPS30 DriveAxle Shaft Exploded Rubber Ring AssemblyDrive Plate Assembly Speed SelectorEngine Mounting Plate Complete LCT EngineFrame 427963X428Idler Pulley Impeller BeltTraction Belt Idler ARM BracketRepair Parts Snow Thrower Model PP414EPS30 Wheels Cable Bracket RH Wheel Assembly LHCable Bracket LH 422663 Repair Parts Snow Thrower Model PP414EPS30 BAG of PartsSafety Ignition KEY Repair Parts Snow Thrower Model PP414EPS30 Decals Service Notes Service Notes Limited Warranty