Poulan 435557, 96198003101 owner manual Maintenance

Page 14

MAINTENANCE

GENERAL RECOMMENDATIONS

The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your snow thrower. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season.

•Once a year, you should replace the spark plug and check belts for wear. A new spark plug will help your engine run better and last longer.

•Follow the maintenance schedule in this manual.

NOTE: Use only Original Equipment Manufacturer (OEM) parts to service this unit. Failure to do so can cause the unit to malfunction and pose a risk of injury to the operator.

BEFORE EACH USE

1.Check engine oil level.

2.Check for loose fasteners.

3.Check controls to be sure they are functioning properly.

LUBRICATION

Keep your snow thrower well lubricated (See “LUBRICATION CHART”).

LUBRICATION CHART

SAE 5W-30 Motor Oil

See “ENGINE” in

Maintenance section

General

Purpose

Grease

Pivot points

Engine

Auger

oil

grease fittings

SNOW THROWER

Always observe the safety rules when performing any maintenance.

TIRES

•Maintain proper air pressure in both tires (14–17 P.S.I.).

•Keeptiresfreeofgasolineandoil,whichcanharmrubber.

NOTE: To seal tire punctures and prevent flat tires due

 

to slow leaks, tire sealant may be purchased from your

 

local parts dealer. Tire sealant also prevents tire dry rot

14

and corrosion.

BELTS

Check belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigTo USE Drift Cutters See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Exploded KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger HousingScrapper BAR Auger BearingSkid Plate LH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate RHCARRIAGEBOLT5/16−18X.750 Weight BARDrift Cutter BAR Plastic WasherDeflector Weldment Deflector Control AssemblyChute Weldment Deflector SealCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadRepair Parts Snow Thrower Model PP414EPS30 Handles Lower Handle Loop Handle LHLoop Handle RH Pivot Support WeldmentHandle Knob SpacerKnob RED Washer 3/8Carriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Sprocket Repair Parts Snow Thrower Model PP414EPS30 DriveAxle Shaft Exploded Speed Selector AssemblyDrive Plate Assembly Rubber Ring427963X428 Complete LCT EngineFrame Engine Mounting PlateIdler ARM Bracket Impeller BeltTraction Belt Idler PulleyRepair Parts Snow Thrower Model PP414EPS30 Wheels Cable Bracket RH Wheel Assembly LHCable Bracket LH 422663 Repair Parts Snow Thrower Model PP414EPS30 BAG of PartsSafety Ignition KEY Repair Parts Snow Thrower Model PP414EPS30 Decals Service Notes Service Notes Limited Warranty
Top Page Image Contents