Poulan 96192000200, 199340 owner manual To Remove Wheels See Fig

Page 16

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt

must be fully seated in pulley groove when bringing

 

the snow thrower together.

16

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lock- washer and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

 

AUGER

SQUARE

 

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

 

 

AUGER PULLEY

 

 

 

 

BOLT

LOCK

 

 

 

WASHER

FRAME

AUGER

 

 

HOUSING

 

 

FIG. 21

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingWhen traction drive control lever is engaged Using the CLEAN-OUT Tool See FigWhen cleaning, repairing, or inspecting, make Stopped. Disconnect the spark plug wireScraper BAR Before Starting the EngineTo Start Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Cleaning EngineTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes Limited Warranty

199340, 96192000200 specifications

The Poulan 96192000200, also known as the Poulan Pro 199340, is a powerful and efficient chainsaw designed for both homeowners and professional users. This versatile tool combines performance with user-friendly features, making it an ideal choice for a variety of cutting tasks, including tree pruning, firewood cutting, and general yard maintenance.

One of the standout features of the Poulan 96192000200 is its powerful engine. Equipped with a robust 50cc two-stroke engine, this chainsaw delivers impressive power, allowing users to tackle larger, tougher jobs with ease. The engine is designed to provide reliable and consistent performance, ensuring that it can cut through hardwoods and thicker branches without a hitch.

In addition to its power, the Poulan 96192000200 also incorporates advanced technology aimed at enhancing user experience and safety. The chainsaw features a patented OxyPower technology, which optimizes fuel consumption while minimizing emissions. This not only makes the chainsaw environmentally friendly but also improves its efficiency, allowing for longer run times between refueling.

The chain brake system is another notable characteristic of this model. The chain brake instantly stops the chain when activated, providing added safety for the operator. This feature is especially important during kickback situations, ensuring that users remain protected while operating the saw.

Furthermore, the Poulan 96192000200 is designed with ease of use in mind. It features an adjustable automatic chain oiler, which ensures that the chain receives adequate lubrication during operation, reducing wear and prolonging the life of the chain and bar. The tool-less air filter and spark plug cover also make maintenance a breeze, allowing users to quickly access and clean these components without the need for additional tools.

The ergonomic design of the chainsaw is another highlight. With a lightweight construction and well-placed grip handles, the Poulan 96192000200 minimizes user fatigue during extended use. This makes it suitable for both casual users and professionals who may spend hours operating the tool.

Overall, the Poulan 96192000200, 199340 chainsaw stands out as a reliable, powerful, and user-friendly option for anyone in need of a high-performance cutting tool. With its combination of advanced technology, safety features, and ergonomic design, it’s a strong contender for both residential and commercial applications.
Top Page Image Contents