Poulan 96192002201, 422080 Snow Throwing Tips, Before Stopping, If Recoil Starter has Frozen

Page 12

OPERATION

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in FAST position.

3.Rotate choke control to FULL position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

6.Push the primer three (3) times.

7.Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu- ous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

8.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

9.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the OFF position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place throttle control in FAST position.

3.Rotate choke control to FULL position.

4.Push the primer four (4) times if the temperature is below 15°F/–10°C, or two (2) times if temperature is between 15° and 50°F/–10°C and 10°C. If temperature is above 50°F/10°C, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the OFF position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

Always operate the snow thrower with the engine at full throttle. Full throttle offers the best performance.

Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the throttle, to adjust speed.

It is easier and more efficient to remove snow imme- diately after it falls.

The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

Slightly overlap each successive path to ensure all snow will be removed.

Throw snow downwind whenever possible.

Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditionsimpair vis- ibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

12

Image 12
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Unfold Upper HandleInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine To Start EngineSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Scrapper BARAuger 24 LH Auger 24 RHAuger Bearing Bearing PlugChute Weldment Deflector WeldmentDeflector Seal StrapLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley PivotPanel Bracket LH Panel Bracket RH Handle Grip405784X479 Pivot Support Weldment Spacer RetainerKnob RED Handle KnobImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomWire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT5524ES Drive Speed Selector Assembly Drive Plate AssemblyShoulder Screw END PlateAxle Shaft Roll PIN 3/16Sprocket Clik PINKEY Part Description Engine Tecumseh Model LH195SP-67510D 417014X505 Engine Mount PlateBelt Cover Traction BeltImpeller Belt Repair Parts Snow Thrower - Model Number XT5524ES Wheels Wheel Assembly LHSafety Ignition KEY Part KEY Description35062 DECAL, Danger DECAL, Poulan PRODECAL, DANGER, Deflector DECAL, InstructionService Notes Service Notes Limited Warranty

XT5524ES, 422080, 96192002201 specifications

The Poulan XT5524ES is a powerful and versatile snow blower designed for residential use, making winter clean-up easier and more efficient. With a strong emphasis on durability and performance, this model is equipped with features that facilitate effective snow removal from driveways, walkways, and other outdoor areas.

One of the main features of the XT5524ES is its robust 24-inch clearing width. This allows users to tackle larger areas in less time, removing snow quickly and effectively. The machine is powered by a reliable 208cc engine, providing ample horsepower to handle heavy snowfalls and tough winter conditions. The electric start feature simplifies operation, enabling users to start the snow blower effortlessly with just the push of a button.

The XT5524ES comes with a durable metal auger that efficiently breaks up and collects snow, allowing for optimal snow throwing capabilities. It is capable of throwing snow up to 40 feet, depending on conditions, which helps in clearing out driveways and sidewalks without constantly needing to reposition the machine.

In terms of maneuverability, the Poulan XT5524ES features a 180-degree adjustable chute, allowing the operator to easily direct the discharged snow. This adjustable chute can be controlled from the operator's position, giving users the flexibility to manage snow placement effectively. The snow blower’s addition of power steering enhances its maneuverability, making it easier to navigate around obstacles and tight spaces.

Another notable characteristic of this model is its six-speed transmission, which includes four forward speeds and two reverse speeds. This feature ensures that users can adjust their speed depending on the snow conditions and the size of the area being cleared.

Built with user comfort in mind, the XT5524ES sports comfort grip handles designed to minimize fatigue during prolonged use. Its heavy-duty tires provide excellent traction on various surfaces, ensuring stability even in slippery conditions.

Additionally, the Poulan XT5524ES is designed for easy maintenance, with accessible components that allow for quick inspections and repairs. Its robust construction and high-quality materials ensure longevity, making it a reliable choice for winter snow removal tasks.

In summary, the Poulan XT5524ES is a feature-rich snow blower that combines power, efficiency, and user-friendly design, making it an ideal solution for homeowners looking to tackle winter snow challenges with ease.