Poulan 422083, 96192002202 owner manual Storage, Other

Page 17

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex-

17 haust area is still warm.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Service Notes Exploded KEY Part Description Auger Assembly LH Auger HousingAuger Assembly RH Scrapper BARBearing Plug Auger BearingDeflector Weldment Chute WeldmentDeflector Seal StrapRotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley PivotHandle Grip Panel Bracket LH Panel Bracket RHLower Tube Pivot SupportRetainer SpacerKnob RED Handle KnobCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Console Panel Wire HarnessHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower - Model Number XT5524ES Drive Drive Plate Assembly Speed Selector AssemblyShoulder Screw END PlateRoll PIN 3/16 Axle ShaftSprocket Clik PIN423184X505 Engine Mount Plate KEY Part Description Engine Tecumseh Model LH195SP-67510DImpeller Belt Belt CoverTraction Belt Wheel Assembly LH Repair Parts Snow Thrower - Model Number XT5524ES Wheels35062 Safety Ignition KEYPart KEY Description DECAL, Auger 5.5 HP 24 Ppro XT DECAL, DangerDECAL, DANGER, Deflector DECAL, Console 5.5 HP 24 Ppro XTService Notes Service Notes Limited Warranty

422083, 96192002202 specifications

The Poulan 96192002202 is a powerful and efficient chainsaw designed for residential and light commercial use. This model stands out for its excellent combination of performance, ease of use, and innovative features, making it a reliable tool for both novice and experienced users alike.

One of the main features of the Poulan 96192002202 is its robust engine. The chainsaw is powered by a 42cc, two-stroke engine that provides ample power for various cutting tasks. This engine design ensures efficient fuel consumption while delivering strong performance, allowing users to tackle everything from small branches to larger logs with ease.

The chainsaw also features a 16-inch bar and chain, perfect for homeowners looking to maintain their landscaping or take on light to moderate cutting jobs. The bar length strikes a balance between maneuverability and cutting capacity, making it an ideal choice for trimming trees, cutting firewood, or clearing brush.

Another important aspect of the Poulan 96192002202 is its user-friendly design. The chainsaw is equipped with an easy-to-access chain brake, enhancing user safety by allowing instant stopping of the chain in emergencies. Additionally, the tool-less chain tensioning feature allows users to adjust the chain quickly and easily without the need for additional tools, saving valuable time during operation.

The lightweight construction of the chainsaw significantly reduces fatigue during extended use. Weighing approximately 10.5 pounds, it can be easily maneuvered during projects, making it perfect for both small and large jobs. The ergonomic design further enhances user comfort, with a well-placed handle that ensures a secure grip and better control.

For added convenience, the Poulan 96192002202 incorporates an integrated fuel gauge, enabling users to monitor fuel levels easily. This feature helps avoid interruption during operation, ensuring a smoother and more efficient working experience.

In conclusion, the Poulan 96192002202 is a versatile and reliable chainsaw that caters to the needs of homeowners and light users. Its powerful engine, user-friendly features, and ergonomic design make it a valuable addition to any toolkit. Whether it's for routine maintenance or occasional cutting tasks, this chainsaw ensures efficient performance and ease of use.
Top Page Image Contents