Poulan 96192002202, 422083 owner manual Troubleshooting

Page 18

TROUBLESHOOTING

See appropriate section in manual unless directed to an authorized service centre/department.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition key

2.

Insert safety ignition key.

 

 

is not inserted.

 

 

 

3.

Out of fuel.

3.

Fill fuel tank with fresh, clean gasoline.

 

4.

Throttle in STOP position

4.

Move throttle to FAST position

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

11.

Water in fuel.

11.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

4.

Water in fuel.

4.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

5.

Carburetor is in need of

5.

Contact an authorized service centre/department.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts. If vibration

vibration

 

augers or impeller.

 

remains, contact an authorized service centre/department.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact an authorized service centre/department.

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Unfold Upper HandleInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine To Start EngineSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Service Notes Exploded KEY Part Description Auger Assembly RH Auger HousingAuger Assembly LH Scrapper BARAuger Bearing Bearing PlugDeflector Seal Chute WeldmentDeflector Weldment StrapRotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley PivotLower Tube Panel Bracket LH Panel Bracket RHHandle Grip Pivot SupportKnob RED SpacerRetainer Handle KnobCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Headlight Bezel Wire HarnessConsole Panel Flood HeadlightRepair Parts Snow Thrower - Model Number XT5524ES Drive Shoulder Screw Speed Selector AssemblyDrive Plate Assembly END PlateSprocket Axle ShaftRoll PIN 3/16 Clik PINKEY Part Description Engine Tecumseh Model LH195SP-67510D 423184X505 Engine Mount PlateBelt Cover Traction BeltImpeller Belt Repair Parts Snow Thrower - Model Number XT5524ES Wheels Wheel Assembly LHSafety Ignition KEY Part KEY Description35062 DECAL, DANGER, Deflector DECAL, DangerDECAL, Auger 5.5 HP 24 Ppro XT DECAL, Console 5.5 HP 24 Ppro XTService Notes Service Notes Limited Warranty

422083, 96192002202 specifications

The Poulan 96192002202 is a powerful and efficient chainsaw designed for residential and light commercial use. This model stands out for its excellent combination of performance, ease of use, and innovative features, making it a reliable tool for both novice and experienced users alike.

One of the main features of the Poulan 96192002202 is its robust engine. The chainsaw is powered by a 42cc, two-stroke engine that provides ample power for various cutting tasks. This engine design ensures efficient fuel consumption while delivering strong performance, allowing users to tackle everything from small branches to larger logs with ease.

The chainsaw also features a 16-inch bar and chain, perfect for homeowners looking to maintain their landscaping or take on light to moderate cutting jobs. The bar length strikes a balance between maneuverability and cutting capacity, making it an ideal choice for trimming trees, cutting firewood, or clearing brush.

Another important aspect of the Poulan 96192002202 is its user-friendly design. The chainsaw is equipped with an easy-to-access chain brake, enhancing user safety by allowing instant stopping of the chain in emergencies. Additionally, the tool-less chain tensioning feature allows users to adjust the chain quickly and easily without the need for additional tools, saving valuable time during operation.

The lightweight construction of the chainsaw significantly reduces fatigue during extended use. Weighing approximately 10.5 pounds, it can be easily maneuvered during projects, making it perfect for both small and large jobs. The ergonomic design further enhances user comfort, with a well-placed handle that ensures a secure grip and better control.

For added convenience, the Poulan 96192002202 incorporates an integrated fuel gauge, enabling users to monitor fuel levels easily. This feature helps avoid interruption during operation, ensuring a smoother and more efficient working experience.

In conclusion, the Poulan 96192002202 is a versatile and reliable chainsaw that caters to the needs of homeowners and light users. Its powerful engine, user-friendly features, and ergonomic design make it a valuable addition to any toolkit. Whether it's for routine maintenance or occasional cutting tasks, this chainsaw ensures efficient performance and ease of use.
Top Page Image Contents