Poulan 96192001903, 421474 owner manual Install Traction Drive Control ROD See Figs

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP

OPENING

DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

6

Image 6

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineDrive speed control lever used to select forward or HOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR ADD Gasoline See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Remove the klik pin and remove wheel from axleStorage OtherTroubleshooting Scrapper BAR Auger HousingKEY Part Description Auger BearingSkid Plate LH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate RHExploded Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleyWeight BAR 181160X479 Drift Cutter BARPlastic Washer Deflector Weldment Deflector Control AssemblyChute Weldment Deflector SealKEY Part Repair Parts Snow Thrower Model PP11530ES Handles Lower Handle Loop Handle LHLoop Handle RH Pivot Support WeldmentHandle Knob SpacerKnob RED Washer 3/8Carriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Repair Parts Snow Thrower Model PP11530ES Drive Axle ShaftSprocket Item 43 Exploded END Plate Speed Selector AssemblyDrive Plate Assembly Bottom PANENGINE, TEC FrameEngine Mount Plate Belt Cover Traction BeltImpeller Belt Cable Bracket LH Repair Parts Snow Thrower Model PP11530ES WheelsWheel Assembly LH Cable Bracket RHWheel Lobe CoverWheel Driver Retainer Ring Clutch SlideRepair Parts Snow Thrower Model PP11530ES BAG of Parts Safety Ignition KEY35062 Repair Parts Snow Thrower Model PP11530ES Decals 421474 421475Limited Warranty