Poulan 421474 Install Discharge Chute / Chute Rotator Head See Fig, Check Tire Pressure

Page 7

ASSEMBLY / PRE-OPERATION

INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotator head over chute bracket. If neces- sary, rotatechute assembly to align square and pin on un- derside of chute rotator head with holes in chute bracket.

3.With chute rotator head and chute bracket aligned, position chute rotator head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE

 

 

ROTATOR

 

3/8 LOCKNUT

HEAD

 

 

 

 

3/8 WASHER

 

 

PIN

 

 

THREADED

 

 

STUD

 

ALIGN BEFORE

ROTATOR HEAD

CHUTE

MOUNTING

BRACKET

TIGHTENING LOCKNUT

BRACKET

FIG. 7

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut as shown. Tighten securely.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

1/4-20

SPRING

CHUTE

SHOULDER

DEFLECTOR

BOLT

 

 

HOOK

NYLON

BETWEEN HEX

WASHER

NUTS

 

ON CHUTE

1/4-20

ROTATER HEAD

LOCKNUT

 

 

5/16-18

 

CARRIAGE

 

BOLT

CABLE

 

EYELET

 

REMOTE

 

CABLE

 

BRACKET

 

5/16-18

 

LOCKNUT

 

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

7

Image 7
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsDrive speed control lever used to select forward or Stopping HOW to USE Your Snow ThrowerTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigADD Gasoline See Fig Before Starting the EngineScraper BAR Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Remove the klik pin and remove wheel from axle To Remove Wheels See FigOther StorageTroubleshooting Auger Bearing Auger HousingKEY Part Description Scrapper BARSkid Plate RH Auger Assembly 30 LHAuger Assembly 30 RH Skid Plate LHExploded Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Bearing181160X479 Drift Cutter BAR Weight BARPlastic Washer Deflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentKEY Part Repair Parts Snow Thrower Model PP11530ES Handles Pivot Support Weldment Loop Handle LHLoop Handle RH Lower HandleWasher 3/8 SpacerKnob RED Handle KnobCarriage Bolt 5/16−18 X 155377 NUT 5/16−18 169675 Axle Shaft Repair Parts Snow Thrower Model PP11530ES DriveSprocket Item 43 Exploded Bottom PAN Speed Selector AssemblyDrive Plate Assembly END PlateFrame ENGINE, TECEngine Mount Plate Traction Belt Belt CoverImpeller Belt Cable Bracket RH Repair Parts Snow Thrower Model PP11530ES WheelsWheel Assembly LH Cable Bracket LHClutch Slide CoverWheel Driver Retainer Ring Wheel LobeSafety Ignition KEY Repair Parts Snow Thrower Model PP11530ES BAG of Parts35062 421474 421475 Repair Parts Snow Thrower Model PP11530ES DecalsLimited Warranty