Poulan 437920, 96192004501 owner manual Meets A.N.S.I. Safety Requirements

Page 8

OPERATION

MUFFLER

GASOLINE

FILLER CAP

CHOKE

CON-

TROL

SAFETY

IGNITION

KEY

ON / OFF

SWITCH

PRIMER

FUEL SHUT-OFF VALVE

RECOIL (AUXILIARY) STARTER HANDLE

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

ELECTRIC

STARTAUGER

BUTTONCONTROL LEVER

POWER

CORD

PLUG

CHUTE

DEFLECTOR

DISCHARGE

CHUTE

CLEAN-OUT

TOOL

FIG. 8

DRIVE

SPEED CONTROL LEVER

DISCHARGE CHUTE

CONTROL LEVER

TRACTION DRIVE

CONTROL LEVER

LIGHT

CHUTE

DEFLECTOR

KNOB

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke control - used for starting a cold engine.

ON / OFF switch - used to STOP the engine.

Traction drive control lever - used to engage power- propelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the direc- tion the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

8

Image 8

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Adjust Skid Plates See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Exploded KEY Part Description Tool ClipAuger Housing Scraper BARAuger 27 LH Auger 27 RHAuger Bearing Bearing PlugSkid Plate LH Skid Plate RHChute Weldment Deflector WeldmentDeflector Seal StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model XT627ES Handles Loop Handle LHLoop Handle RH Lower Handle180480 Impeller RODTraction ROD RetainerSpacer Knob REDHandle Knob Washer 3/8Wire Harness Console PanelHeadlight Bezel Flood HeadlightRepair Parts Snow Thrower Model XT627ES Drive Speed Selector Repair Parts Complete LCT Engine Frame428684 Repair Parts Snow Thrower Model XT627ES Wheels Wheel Assembly LH432335X428 432336X428422663 Repair Parts Snow Thrower Model XT627ES BAG of PartsSafety Ignition KEY Repair Parts Snow Thrower Model XT627ES Decals DECAL, DangerDECAL, Instruc DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty