Poulan 96192003500, 428861, XT11530ES Parts Packed Separately in Carton, Assembly / PRE-OPERATION

Page 4

PARTS PACKED SEPARATELY IN CARTON

(1) FUEL STABILIZER PACKET

(1) MULTI-

 

WRENCH

 

(180684)

(1) POWER CORD

SAFTEY IGNITION KEY(S)

(198563)

(193071)

(1) AUGER CONTROL ROD

(1) DISCHARGE CHUTE

EXTRA SHEAR BOLTS AND NUTS

(2) SHOULDER

(2) LOCKNUTS

BOLT 1/4-20 x 1-3/4

1/4-20

(192090)

(73800400)

ROTATOR HEAD MOUNTING

(3) RETAINER SPRINGS (169675)

(1) WASHER 3/8

(1) LOCKNUT 3/8

(19131316)

(73800600)

CHUTE DEFLECTOR REMOTE CONTROL

(1) LOCKNUT

(1) CARRIAGE BOLT

(1) LOCKNUT

(1) SHOULDER

(1) SPRING

5/16-18

5/16-18 x 5/8

1/4-20

BOLT 1/4-20

(751153)

(72250505)

(191730)

(179829)

(184505)

(2)FLAT WASHERS

(2)CARRIAGE BOLTS 3/8-16 x 2.25

(2)HANDLE KNOBS

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety

 

2.

Cut down all four corners of carton and lay panels flat.

before you attempt to assemble or operate your new

 

3.

Remove the two (2) screws securing the auger housing

snow thrower. Reading the entire manual will familiar-

 

 

 

to the pallet.

ize you with the unit, which will assist you in assembly,

 

 

 

4.

Remove all packing materials except plastic tie holding

operation and maintenance of the product.

 

 

 

speed control rod to lower handle.

Your new snow thrower has been assembled at the factory

 

 

 

5. Remove the two (2) plastic ties securing the upper

with the exception of those parts left unassembled for ship-

 

 

 

handle to the pallet.

ping purposes. All parts such as nuts, washers, bolts, etc.,

 

 

 

6. Remove snow thrower from carton and check carton

necessary to complete the assembly have been placed in

 

the parts bag. To ensure safe and proper operation of your

 

 

thoroughly for additional loose parts.

snow thrower, all parts and hardware you assemble must

 

HOW TO SET UP YOUR SNOW THROWER

be tightened securely. Use the correct tools as necessary

 

to ensure proper tightness.

 

TOOL BOX (See Fig. 10)

 

 

REMOVE SNOW THROWER FROM CARTON

 

A toolbox is provided on your snow thrower. The toolbox is

1. Remove all accessible loose parts and parts boxes

 

located on top of the belt cover. Store the extra shear bolts,

4

nuts and multi-wrench provided in parts bag in the toolbox.

from carton.

 

 

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes 23 22 KEY Part Description Auger Housing Auger Assembly 30 LHAuger Assembly 30 RH Scrapper BARAuger Bearing Bearing PlugKnob Black POP RivetShoulder Screw Deflector SpringLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model XT11530ES Handles Loop Handle LHLoop Handle RH Lower Tube180480 Impeller RODTraction ROD RetainerSpacer Knob REDHandle Knob Washer 3/8Wire Harness Interlock SpringInterlock CAM Torsion SpringRepair Parts Snow Thrower Model XT11530ES Drive Assembly Drive Plate AssemblySpeed Selector Rubber RingAxle Shaft SprocketEngine Model Frame423185X505 Engine Mounting PlateCover Assembly Impeller BeltTraction Belt Idler ARM BracketRepair Parts Snow Thrower Model XT11530ES Wheels 01.06.005-A Safety Ignition KEY Repair Parts Snow Thrower Model XT11530ES BAG of Parts193071 181037 Repair Parts Snow Thrower Model XT11530ES DecalsDECAL, Danger Service Notes Service Notes Service Notes Limited Warranty
Top Page Image Contents