Poulan 428861, 96192003500, XT11530ES owner manual Meets A.N.S.I. Safety Requirements

Page 9

OPERATION

GASOLINE

FILLER CAP

MUFFLER

CHOKE CON-

TROL

PRIMER

SAFETY

IGNITION

KEYON / OFF SWITCH

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

ELECTRIC AUGER

START BUTTON CONTROL RECOIL LEVER

(AUXILIARY) STARTER HANDLE

CHUTE

DEFLECTOR

DISCHARGE

CHUTE

CLEAN-OUT

TOOL

FIG. 10

DRIVE

SPEED CONTROL LEVER

DISCHARGE CHUTE

CONTROL LEVER

DEFLECTOR REMOTE

CONTROL LEVER

TRACTION

DRIVE

CONTROL

LEVER

LH TURN

TRIGGER

LIGHT

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

LH and RH turn triggers - used to steer the snow thrower. Choke control - used for starting a cold engine.

ON / OFF switch - used to STOP the engine.

Traction drive control lever - used to engage power- propelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Deflector remote control lever - used to change the distance the snow is thrown.

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

9

Image 9

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer Ignition KEYRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo USE Choke Control See Fig To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Before Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine SpeedOther StorageFuel System Engine OILTroubleshooting Service Notes 23 22 KEY Part Description Auger Assembly 30 LH Auger HousingAuger Assembly 30 RH Scrapper BARBearing Plug Auger BearingPOP Rivet Knob BlackShoulder Screw Deflector SpringCable Assembly Adjustable LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketLoop Handle LH Repair Parts Snow Thrower Model XT11530ES HandlesLoop Handle RH Lower TubeImpeller ROD 180480Traction ROD RetainerKnob RED SpacerHandle Knob Washer 3/8Interlock Spring Wire HarnessInterlock CAM Torsion SpringRepair Parts Snow Thrower Model XT11530ES Drive Drive Plate Assembly AssemblySpeed Selector Rubber RingSprocket Axle ShaftFrame Engine Model423185X505 Engine Mounting PlateImpeller Belt Cover AssemblyTraction Belt Idler ARM BracketRepair Parts Snow Thrower Model XT11530ES Wheels 01.06.005-A Repair Parts Snow Thrower Model XT11530ES BAG of Parts Safety Ignition KEY193071 Repair Parts Snow Thrower Model XT11530ES Decals 181037DECAL, Danger Service Notes Service Notes Service Notes Limited Warranty