Poulan 96198003700, 437738 HOW to USE Your Snow Thrower, Stopping, To USE Choke Control See Fig

Page 10

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating 00155 your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

•Release the auger control lever to stop throwing snow.

ENGINE

1.Move ON / OFF switch to “OFF” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE CHOKE CONTROL (See Fig. 11)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke, turn knob counterclockwise. Slowly turn knob clockwise to disengage.

OFF

 

FULL

 

 

 

 

FIG. 11

TO CONTROL SNOW DISCHARGE (See Fig. 12)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or auger become clogged, shut-off engine and wait for all moving parts to stop. Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

•To change the discharge chute position, press downward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther.

•Press downward on chute deflector control lever and move lever forward to raise the deflector and increase the distance. Move lever back to lower the deflector and decrease the distance. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

CHUTE DEFLECTOR

REMOTE CONTROL LEVER

FIG. 12

TO THROW SNOW (See Fig. 13)

The auger rotation is controlled by the auger control lever located on the right side handle.

•Squeeze auger control lever to handle to engage the auger and throw snow.

•Release the auger control lever to stop throwing snow.

AUGER

CONTROL

LEVER

FIG. 13

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig Before Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH Scrapper BARSkid Plate LH Auger BearingBearing Plug Skid Plate RHPlastic Washer Drift Cutter BARCARRIAGEBOLT5/16−18X.750 Lockwasher 5/16Chute Snow Shield 419822X431 Shield Retainer Strap Knob BlackPOP Rivet Deflector SpringCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLoop Handle RH Repair Parts Snow Thrower Model PP165E30 HandlesLoop Handle LH 427513X431 Pivot Support WeldmentTraction ROD 180480Impeller ROD RetainerHandle Knob SpacerKnob RED Washer 3/8Interlock CAM Wire HarnessInterlock Spring Torsion SpringAxle Shaft Repair PartsDrive SprocketRepair Parts Snow Thrower Model PP165E30 Drive Speed Selector AssemblyDrive Plate Assembly Rubber Ring436146X428 Engine ModelFrame Engine Mount Plate428684 Repair Parts Snow Thrower Model PP165E30 Wheels 432337X421 Wheel Assembly LH432338X421 Safety Ignition KEY Repair Parts Snow Thrower Model PP165E30 BAG of Parts193071 435840 Shifter ROD TOP Shifter ROD BottomKIT Harness Conn B&S DECAL, Danger Repair Parts Snow Thrower Model PP165E30 Decals181037 DECAL, Console Instruction E/F DECAL, DANGER, DeflectorService Notes Limited Warranty

437738, 96198003700, PP165E30 specifications

The Poulan PP165E30 is a robust and versatile chainsaw designed for both professional and home use. Known for its reliability and performance, it stands out with a host of features that make it suitable for various cutting tasks, from felling trees to trimming branches.

One of the key characteristics of the PP165E30 is its powerful 16-inch gas chainsaw engine. The engine is designed to deliver ample power while maintaining efficiency, making it capable of handling tough cutting jobs with ease. The lightweight design of the tool enhances user maneuverability, ensuring that both experienced professionals and novice users can operate it comfortably without fatigue.

A standout feature of the PP165E30 is the inclusion of an automatic oiling system. This technology ensures that the chain remains lubricated during operation, reducing wear and tear on both the chain and guide bar. This not only prolongs the life of the chainsaw but also contributes to smoother cuts and better overall performance. The adjustable oil flow allows users to set the lubrication level according to the specific task at hand, maximizing efficiency.

Safety is paramount in the design of the PP165E30. It comes equipped with a chain brake that acts quickly to stop the chain in the event of kickback, offering peace of mind during operation. The chainsaw also features an anti-vibration system to minimize user fatigue and improve handling, allowing for longer cutting sessions without discomfort.

In terms of maintenance, the Poulan PP165E30 is designed with ease of use in mind. The tool-less access to the air filter and spark plug makes routine maintenance straightforward, helping users keep their equipment in top condition.

Overall, the Poulan PP165E30 is an excellent choice for those who need a reliable chainsaw equipped with advanced technologies and user-friendly features. Its powerful engine, automatic oiling system, and emphasis on safety make it an indispensable tool for anyone looking to tackle outdoor projects efficiently and effectively. Whether you are trimming trees around your home or managing larger landscaping tasks, the PP165E30 is built to meet your cutting needs with precision and power.
Top Page Image Contents