Poulan 437738 To Remove Wheels See Fig, To Adjust Cable Tension See Fig, Carburetor, Engine Speed

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 23)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 23

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

TO ADJUST CABLE TENSION (See Fig. 24)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 24

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Before Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH Scrapper BARSkid Plate LH Auger BearingBearing Plug Skid Plate RHPlastic Washer Drift Cutter BARCARRIAGEBOLT5/16−18X.750 Lockwasher 5/16Chute Snow Shield 419822X431 Shield Retainer Strap Knob BlackPOP Rivet Deflector SpringCable Assembly Heat Shield LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLoop Handle RH Repair Parts Snow Thrower Model PP165E30 HandlesLoop Handle LH 427513X431 Pivot Support WeldmentTraction ROD 180480Impeller ROD RetainerHandle Knob SpacerKnob RED Washer 3/8Interlock CAM Wire HarnessInterlock Spring Torsion SpringAxle Shaft Repair PartsDrive SprocketRepair Parts Snow Thrower Model PP165E30 Drive Speed Selector AssemblyDrive Plate Assembly Rubber Ring436146X428 Engine ModelFrame Engine Mount Plate428684 Repair Parts Snow Thrower Model PP165E30 Wheels Wheel Assembly LH 432337X421432338X421 Repair Parts Snow Thrower Model PP165E30 BAG of Parts Safety Ignition KEY193071 Shifter ROD TOP Shifter ROD Bottom 435840KIT Harness Conn B&S DECAL, Danger Repair Parts Snow Thrower Model PP165E30 Decals181037 DECAL, Console Instruction E/F DECAL, DANGER, DeflectorService Notes Limited Warranty

437738, 96198003700, PP165E30 specifications

The Poulan PP165E30 is a robust and versatile chainsaw designed for both professional and home use. Known for its reliability and performance, it stands out with a host of features that make it suitable for various cutting tasks, from felling trees to trimming branches.

One of the key characteristics of the PP165E30 is its powerful 16-inch gas chainsaw engine. The engine is designed to deliver ample power while maintaining efficiency, making it capable of handling tough cutting jobs with ease. The lightweight design of the tool enhances user maneuverability, ensuring that both experienced professionals and novice users can operate it comfortably without fatigue.

A standout feature of the PP165E30 is the inclusion of an automatic oiling system. This technology ensures that the chain remains lubricated during operation, reducing wear and tear on both the chain and guide bar. This not only prolongs the life of the chainsaw but also contributes to smoother cuts and better overall performance. The adjustable oil flow allows users to set the lubrication level according to the specific task at hand, maximizing efficiency.

Safety is paramount in the design of the PP165E30. It comes equipped with a chain brake that acts quickly to stop the chain in the event of kickback, offering peace of mind during operation. The chainsaw also features an anti-vibration system to minimize user fatigue and improve handling, allowing for longer cutting sessions without discomfort.

In terms of maintenance, the Poulan PP165E30 is designed with ease of use in mind. The tool-less access to the air filter and spark plug makes routine maintenance straightforward, helping users keep their equipment in top condition.

Overall, the Poulan PP165E30 is an excellent choice for those who need a reliable chainsaw equipped with advanced technologies and user-friendly features. Its powerful engine, automatic oiling system, and emphasis on safety make it an indispensable tool for anyone looking to tackle outdoor projects efficiently and effectively. Whether you are trimming trees around your home or managing larger landscaping tasks, the PP165E30 is built to meet your cutting needs with precision and power.
Top Page Image Contents