Poulan 429924 Before Starting the Engine, To Adjust Skid Plates See Fig, Scraper BAR See Fig

Page 12

OPERATION

TO ADJUST SKID PLATES (See Fig. 18)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the 1/2" hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION

 

(LOW GROUND

 

CLEARANCE)

 

 

AUGER

 

HOUSING

 

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 18

SCRAPER BAR (See Fig. 18)

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 19)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 19)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gaso- hol or using ethanol or methanol) can attract moisture which leads to separation and forma- tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

ON / OFF

RECOIL (AUXILIARY)

STARTER HANDLE

SWITCH

 

 

GASOLINE

 

FILLER CAP

CHOKE

ENGINE OIL FILL

CAP / DIPSTICK

CON-

 

TROL

 

 

STARTER

 

BUTTON

SAFETY

 

IGNITION

 

KEY

 

PRIMER

 

 

POWER

 

CORD

FUEL SHUT-OFF VALVE

PLUG

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

12

FIG. 19

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning Snow ThrowerEngine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Auger Housing Auger Assembly 30 LHAuger Assembly 30 RH KEY Part Description23 22 Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyAuger Bearing Bearing PlugDeflector Control Assembly Chute WeldmentDeflector Weldment Deflector SealLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model PR1030ES Handles Repair Parts Handles SpacerKnob RED Handle KnobImpeller ROD Traction RODShifter ROD TOP Shifter ROD BottomWire Harness Lower TubePivot Support Console PanelRepair Parts Snow Thrower Model PR1030ES Drive Axle ShaftSprocket Repair Parts Snow Thrower Model PR1030ES 96192003101DRIVE Assembly Drive Plate AssemblySpeed Selector Rubber RingComplete LCT Engine Frame427963X428 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket LH Cable Bracket RHRepair Parts Snow Thrower Model PR1030ES BAG of Parts Safety Ignition KEY422663 Repair Parts Snow Thrower Model PR1030ES Decals 181037DECAL, Danger DECAL, DANGER, DeflectorLimited Warranty HOP

96192003101, 429924 specifications

The Poulan 429924 and its counterpart, the 96192003101, represent an advanced line of outdoor power equipment designed for both professional and consumer use. These models are well-known for their reliability, performance, and ease of use, making them essential tools for landscaping and yard maintenance tasks.

One of the main features of the Poulan 429924 is its powerful engine designed for optimal cutting performance. This engine provides consistent power, enabling users to tackle tough conditions with ease. The robust construction of the engine ensures longevity, reducing maintenance needs and enhancing reliability over time.

Another significant characteristic of the Poulan 96192003101 is its lightweight design. Weighing significantly less than many competitors, this model allows for increased maneuverability and reduced fatigue during extended use. Users can enjoy a more comfortable experience when trimming, edging, or pruning, even over larger areas.

The technology behind these models includes advanced air filtration systems that promote cleaner operation and extend the life of the engine. This feature is particularly beneficial in dusty environments or when working with tough vegetation, as it helps maintain engine performance and efficiency. Additionally, these models often incorporate easy-start technology, which minimizes the effort required to start the engine, making them user-friendly for individuals of all experience levels.

The Poulan 429924 and 96192003101 emphasize versatility and adaptability. They are compatible with a range of accessories, allowing users to switch between functions quickly. Whether it's switching from trimming grass to tackling thicker brush, these tools can be customized to meet various landscaping needs.

Safety features are another hallmark of these models. Equipped with features like protective guards and safety switches, Poulan has ensured that users can operate their equipment with confidence. The ergonomic handle designs further enhance user control, reducing the risk of accidents while increasing comfort during prolonged use.

In conclusion, the Poulan 429924 and 96192003101 are exemplary models in the outdoor power equipment market, combining power, lightweight design, and advanced technology. Their versatility, reliability, and emphasis on user safety make them ideal choices for both residential and commercial landscape maintenance, ensuring that users can achieve professional results with ease. Whether you're a seasoned professional or a weekend warrior, these models offer the performance and features needed to get the job done efficiently and effectively.
Top Page Image Contents