Poulan 429924 owner manual Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 20)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a spacer, shear bolt and hex nut. Should a foreign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever

is engaged, check to see if the capscrews have sheared. 16

To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 20

TO REMOVE BELT COVER (See Fig. 21)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

Replace belt cover by installing cover and screws and tighten securely.

 

BELT

 

COVER

FRAME

SCREWS

FIG. 21

Image 16
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationSnow Thrower CleaningEngine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Auger Housing Auger Assembly 30 LHAuger Assembly 30 RH KEY Part Description23 22 Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyAuger Bearing Bearing PlugDeflector Control Assembly Chute WeldmentDeflector Weldment Deflector SealLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model PR1030ES Handles Repair Parts Handles SpacerKnob RED Handle KnobImpeller ROD Traction RODShifter ROD TOP Shifter ROD BottomWire Harness Lower TubePivot Support Console PanelAxle Shaft Repair Parts Snow Thrower Model PR1030ES DriveSprocket Repair Parts Snow Thrower Model PR1030ES 96192003101DRIVE Assembly Drive Plate AssemblySpeed Selector Rubber RingComplete LCT Engine Frame427963X428 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket LH Cable Bracket RHSafety Ignition KEY Repair Parts Snow Thrower Model PR1030ES BAG of Parts422663 Repair Parts Snow Thrower Model PR1030ES Decals 181037DECAL, Danger DECAL, DANGER, DeflectorLimited Warranty HOP

96192003101, 429924 specifications

The Poulan 429924 and its counterpart, the 96192003101, represent an advanced line of outdoor power equipment designed for both professional and consumer use. These models are well-known for their reliability, performance, and ease of use, making them essential tools for landscaping and yard maintenance tasks.

One of the main features of the Poulan 429924 is its powerful engine designed for optimal cutting performance. This engine provides consistent power, enabling users to tackle tough conditions with ease. The robust construction of the engine ensures longevity, reducing maintenance needs and enhancing reliability over time.

Another significant characteristic of the Poulan 96192003101 is its lightweight design. Weighing significantly less than many competitors, this model allows for increased maneuverability and reduced fatigue during extended use. Users can enjoy a more comfortable experience when trimming, edging, or pruning, even over larger areas.

The technology behind these models includes advanced air filtration systems that promote cleaner operation and extend the life of the engine. This feature is particularly beneficial in dusty environments or when working with tough vegetation, as it helps maintain engine performance and efficiency. Additionally, these models often incorporate easy-start technology, which minimizes the effort required to start the engine, making them user-friendly for individuals of all experience levels.

The Poulan 429924 and 96192003101 emphasize versatility and adaptability. They are compatible with a range of accessories, allowing users to switch between functions quickly. Whether it's switching from trimming grass to tackling thicker brush, these tools can be customized to meet various landscaping needs.

Safety features are another hallmark of these models. Equipped with features like protective guards and safety switches, Poulan has ensured that users can operate their equipment with confidence. The ergonomic handle designs further enhance user control, reducing the risk of accidents while increasing comfort during prolonged use.

In conclusion, the Poulan 429924 and 96192003101 are exemplary models in the outdoor power equipment market, combining power, lightweight design, and advanced technology. Their versatility, reliability, and emphasis on user safety make them ideal choices for both residential and commercial landscape maintenance, ensuring that users can achieve professional results with ease. Whether you're a seasoned professional or a weekend warrior, these models offer the performance and features needed to get the job done efficiently and effectively.