Poulan 428707 Snow Throwing Tips, To Start Engine, Before Stopping, If Recoil Starter has Frozen

Page 12

OPERATION

TO START ENGINE

•Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Move choke control to “FULL” position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

NOTE: Do not use primer when starting engine with the electric starter.

6. Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu- ous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

7.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

8.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.

•It is easier and more efficient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting 23 22 KEY Part Description Auger Housing Auger Assembly LHAuger Assembly RH Scrapper BARAuger Bearing Bearing PlugKnob Black POP RivetWasher Plastic WasherLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadRepair Parts Snow Thrower Model Number 96194000801 Handles 196944X007 Panel Bracket LH 196943X007 Panel Bracket RH Handle GripLower Tube Pivot SupportCarriage Bolt 5/16-18 X 155377 NUT 5/16-18 169675 Part KEY Description Repair Parts Snow Thrower Model Number 96194000801 Drive Assembly Drive Plate AssemblySpeed Selector Rubber RingRepair Parts Drive Snow Thrower Model Number Axle ShaftRoll PIN 3/16 SprocketComplete LCT Engine Frame427963X428 Engine Mounting PlateImpeller Belt Traction BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower Model Number 96194000801 Wheels Wheel Assembly LH187831X417 187866X417Power Cord Safety Ignition KEYRetainer PIN WrenchRepair Parts Snow Thrower Model Number 96194000801 Decals 181037DECAL, Danger DECAL, DANGER, DeflectorLimited Warranty

96194000801, 961940008, 428707 specifications

The Poulan 428707,96194000801,961940008 is a powerful and versatile outdoor power tool designed for landscaping and yard maintenance. This model impresses with its robust features, advanced technologies, and user-oriented characteristics that cater to both professional landscapers and DIY enthusiasts.

One of the standout features of the Poulan 428707 is its potent engine, designed to deliver reliable performance for a variety of outdoor tasks. The engine's efficiency enables it to tackle demanding jobs such as trimming, edging, and clearing debris, making it an essential tool for maintaining a pristine lawn or garden. The lightweight design of the equipment enhances maneuverability, ensuring that users can easily navigate tight spaces and complex terrains without straining themselves.

In terms of technology, the Poulan 428707 incorporates low-emission capabilities that are compliant with environmental regulations. This means that users can enjoy the powerful performance of the tool while minimizing their environmental footprint. The ergonomic design is another notable technological advancement; it features comfortable grips and adjustable handles, allowing users to work for extended periods without discomfort or fatigue.

The Poulan 428707 is equipped with a range of cutting attachments, offering versatility for different tasks. Whether you need to cut through thick brush or perform delicate trimming, this tool can adapt to meet your needs. The easy-to-use system for swapping out attachments further simplifies the process, making it user-friendly for those who may not have previous experience with such equipment.

Durability is a key characteristic of the Poulan 428707, as it is constructed from high-quality materials designed to withstand wear and tear. This durability ensures longevity, providing users with a reliable tool that can handle seasonal demands year after year.

Overall, the Poulan 428707,96194000801,961940008 stands out as a top choice in outdoor power tools due to its functionality, innovative technologies, and robust build quality. Its combination of power, efficiency, and user-friendly design makes it an indispensable addition to any outdoor maintenance arsenal, positioning it as a leading option for individuals looking to enhance their landscaping capabilities. Whether you're maintaining your home garden or managing larger landscaping projects, this tool will help you achieve professional results with ease.
Top Page Image Contents