Poulan 96194000900 Gearbox Assembly, Bearing, Impeller Pulley, Discharge Base, Tool Clip, Plug

Page 23

REPAIR PARTS SNOW THROWER - MODEL 961940009 (96194000900) AUGER HOUSING / IMPELLER ASSEMBLY

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1175321X479 IMPELLER

2427148 GEARBOX ASSEMBLY

3	188909	BEARING
4	427146	IMPELLER PULLEY
5	175322	DISCHARGE BASE

6178675X008 CORNER BRACKET

7192199 CLEAN OUT TOOL

8	405400	TOOL CLIP
9	73800400	NUT 1/4-20
10	74780426	SCREW 1/4-20 X .625
11	427942	NUT 5/16-18
12	163183	SCREW 5/16-18 X .625
13	427145	IMPELLER HUB
14	427154	IMPELLER SLEEVE
15	73900600	NUT 3/8-16
16	180355	CARRIAGE BOLT
17	194189	SCREW 13-16 X .625
18	407760	PLUG
19	427302	GEARBOX COVER RH
20	427345	GASKET
21	407770	SEAL
22	407762	BEARING
23	174697	THRUST WASHER 1.00
24	407763	WORM GEAR
25	407764	AUGER SHAFT
26	189282	SQUARE KEY
27	407758	BEARING
28	174683	THRUST WASHER
29	427147	IMPELLER SHAFT
30	7836M	ROLL PIN
31	174681	THRUST WASHER
32	174684	THRUST BEARING
33	407769	BEARING
34	407768	O-RING
35	407767	SCREW 5/16-18 X .750
36	427317	GEARBOX COVER LH
37	192090	SHEAR BOLT

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

23

Image 23

Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningSnow Thrower Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting KEY Part Description Auger HousingAuger Assembly 30 LH Auger Assembly 30 RH23 22 Impeller Pulley Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool BearingBearing Plug Auger BearingShield Retainer Strap Knob BlackPOP Rivet Chute Snow ShieldRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadInterlock CAM Loop Handle LHLoop Handle RH Interlock SpringWasher 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller RODTraction ROD Shifter ROD TOPConsole Panel Wire HarnessLower Tube Pivot SupportSprocket Axle ShaftExploded Rubber Ring AssemblyDrive Plate Assembly Speed Selector427963X428 Cover AssemblyComplete LCT Engine FrameIdler Pulley Impeller BeltTraction Belt Idler ARM BracketClutch Slide CoverWheel Driver Retainer Ring Wheel LobeCable Bracket RH Cable Bracket LH422663 Safety Ignition KEYDECAL, Instruction 181037DECAL, Danger DECAL, DANGER, DeflectorHOP Limited Warranty