Poulan 428695 Impeller Belt, Traction Belt, Idler ARM Bracket, Idler Pulley, Pulley ENG Impeller

Page 36

REPAIR PARTS SNOW THROWER - - MODEL NO. PR827ES (96192003001)

CHASSIS / ENGINE / PULLEYS

23		22	14
24			14	21
24				21
				20
11
14	21		20	19
13			20	18
13				18
12				17
12	14			16
		15		16
		15		6
				6
	7
10
				5
8				4
8				3
				3
				9

1

2

01.21.003-B

KEY	PART		KEY	PART
NO.	NO.	DESCRIPTION	NO.	NO.	DESCRIPTION
1	408007	IMPELLER BELT	13	74780520	SCREW 5/16-18 X 1 .00
2	419744	TRACTION BELT	14	59289	WASHER
3	423723X479	IDLER ARM BRACKET	15	73800500	NUT 5/16-18
4	180523	IDLER PULLEY	16	851084	SCREW 3/8-24 X 1.375
5	426589	NUT 5/16-18	17	400026	WASHER
6	74780524	SCREW 5/16-18 X 1 .50	18	426491	PULLEY ENG IMPELLER
7	423990X479	IDLER BRACKET	19	426490	PULLEY ENG TRACTION
8	428867	SCREW 5/16-18 X .625	20	74610516	SCREW 5/16-18 X 1 .00
9	424297	SHOULDER BOLT 5/16-18	21	10040500	LOCKWASHER 5/16
		X .500	22	155452	BELT GUIDE
10	751153	NUT 5/16-18 NYLOCK	23	11050500	LOCKWASHER 5/16
11	187786	TRACTION IDLER ARM	24	175331	IDLER BUSHING
12	180522	TRACTION PULLEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

36

Image 36

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Choke Control See Fig To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance Cleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Service Notes Auger Housing KEY Part DescriptionScraper BAR Auger BearingAuger 27 LH Auger 27 RHSkid Plate LH Skid Plate RH23 22 Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyLEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator HeadKnob Black POP RivetShoulder Screw Deflector SpringRepair Parts Snow Thrower - Model NO. PR827ES Handles Lower Tube Pivot SupportInterlock Spring Interlock CAMSpacer Knob REDHandle Knob Washer 3/8Impeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD BottomRepair Parts Snow Thrower - Model NO. PR827ES Drive Assembly Drive Plate AssemblySpeed Selector Rubber RingAxle Shaft Roll PIN 3/16Sprocket Clik PINCover Assembly Engine Model 12A114Frame 423185X428Impeller Belt Traction BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower - Model NO. PR827ES Wheels Wheel Assembly LH187833X421 187865X421Repair Parts Snow Thrower - Model NO. PR827ES BAG of Parts Safety Ignition KEY193071 Repair Parts Snow Thrower - Model NO. PR827ES Decals181037 DECAL, DangerLimited Warranty