MTD E610E, E660G, E640F manual Operation

Page 11

TRACTION DRIVE/AUGER CLUTCH LOCK

(See Figure 14)

The traction drive clutch is located on the right handle. Squeeze the traction drive clutch to engage the wheel drive. Release to stop.

This same lever also locks the auger clutch so you can turn the chute crank without interrupting the snow throwing process. If the auger drive clutch is engaged with the traction drive clutch engaged, the operator can release the auger drive clutch (on the left handle) and the augers will remain engaged. Release the traction drive clutch to stop both the augers and wheel drive (auger drive clutch must also be released).

CHUTE CRANK (See Figure 14)

The chute crank is located on left hand side of the snow thrower.

To change the direction in which snow is thrown, turn chute crank as follows:

1.Crank clockwise to discharge to the left.

2.Crank counterclockwise to discharge to the right.

THROTTLE CONTROL (See Figure 17)

The throttle control is located on the engine. It regu- lates the speed of the engine.

SAFETY IGNITION SWITCH (See Figure 17)

The ignition key must be inserted in the switch before the unit will start. Remove the ignition key when snow thrower is not in use.

SECTION 7: OPERATION

BEFORE STARTING

WARNING: Observe all Warning Labels on the snow thrower prior to use. See Figure 1.

Your snow thrower is shipped with oil; however, you must check the oil level before operating. Be careful not to overfill.

The spark plug wire was disconnected for safety. Attach spark plug wire to spark plug before starting.

GAS AND OIL FILL-UP

Check oil level and add oil if necessary. Service the engine with gasoline as instructed in the separate engine manual packed with your snow thrower. Read instructions carefully.

WARNING: Never fill fuel tank indoors. Never fill fuel tank with engine running or while engine is hot. Do not smoke when filling fuel tank.

TO START ENGINE

1. Attach spark plug wire to spark plug. Make

certain the metal loop on end of the spark plug

FUEL SHUT-OFF VALVE

The fuel shut-off valve, located under fuel tank, controls fuel flow from tank. (If equipped)

Closed

Open

Figure 16

wire (inside the boot) is fastened securely over

the metal tip on the spark plug. See Figure 18.

Metal Loop

on Spark

Plug Wire

Rubber Boot

Choke

Primer

 

 

 

Rope

Ignition

Throttle

Start

Handle

Key

Control

 

 

Figure 17

 

Figure 18

2.Make certain the fuel cutoff valve is in the OPEN (vertical) position.

3.Make certain the auger and drive clutch levers are in the disengaged (released) position.

4.Move throttle control up to FAST position. Insert ignition key into slot. See Figure 19. Be certain it snaps into place. Do not turn key.

ENGINE WILL NOT START

UNLESS IGNITION KEY IS IN-

SERTED INTO IGNITION

SLOT IN CARBURETOR

COVER. DO NOT TURN IGNI-

TION KEY.

11

Image 11
Contents MTD Products INC. P.O. BOX 368022 CLEVELAND, Ohio Important Read Safety Rules and Instructions CarefullyOperation Important Safe Operation PracticesTraining PreparationMaintenance and Storage Calling Customer Support Finding Your Model NumberContents of Hardware Pack Loose Parts in Carton See Figure Assembly InstructionsTools Required for Assembly UnpackingAttaching the Clutch Cables Attaching the Handle AssemblyHardware a Attaching the Chute Crank Hardware C Attaching the Chute Assembly Hardware BAuger Drive Clutch Final AdjustmentsAttaching the Shift ROD Hardware D Tire Pressure Pneumatic Tires Traction Drive Clutch and Shift Lever AdjustmentAdjusting the Skid Shoes ControlsOperation To Stop Engine Electric StarterRecoil Starter Adjustments Lubrication Maintenance Drive Belt Belt Removal and Replacement Auger BeltsChanging Friction Wheel Rubber OFF-SEASON StorageTrouble Shooting Guide Gear Assembly All Models Blower Housing Part Description QTY Handle Assembly Handle Assembly Frame Assembly Wheel Assemblies Model no Size Engine and V-Belts E640F E660G MANUFACTURER’S Limited Warranty for