Poulan PP1053ES, 421471 owner manual Snow Thrower, Engine, Cleaning

Page 15

MAINTENANCE

SNOW THROWER

Always observe safety rules when performing maintenance.

TIRES

•Maintain proper air pressure in both tires (14–17 P.S.I. / 19-24.5 N-m).

•Keep tires free of gasoline / oil, which can harm rubber.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

V-BELTS

Check V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your dealer. Using other than OEM belts can cause personal injury / damage to the thrower.

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs atten- tion is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce

a year if the snow thrower is not used for 25 hours in one year. 15

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Rotator Head Mounting Chute Deflector Remote ControlParts Packed Separately in Carton EXT RA Shear Bolts and NutsUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USECleaning Snow ThrowerEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Exploded KEY Part Description Bearing Plug Auger HousingScrapper BAR Auger BearingAuger Assembly 30 RH Auger Assembly 30 LHDeflector Seal Deflector Control AssemblyChute Weldment Deflector WeldmentPulley Pivot LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model PP1053ES Handles Washer 3/8 SpacerKnob RED Handle KnobShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPPart KEY Description Repair Parts Snow Thrower Model PP1053ES 96192001803DRIVE Bottom PAN Speed Selector AssemblyDrive Plate Assembly END PlateRepair Parts Snow Thrower Model PP1053ES Drive Axle ShaftSprocket KEY Part Description Tecumseh Engine Model LH358SA-159628A417014X428 Engine Mount Plate Belt Cover Traction BeltImpeller Belt Repair Parts Snow Thrower Model PP1053ES Wheels Cable Bracket RH Cable Bracket LHRepair Parts Snow Thrower Model PP1053ES BAG of Parts Safety Ignition KEY35062 Repair Parts Snow Thrower Model PP1053ES Decals 181037DECAL, Danger Service Notes Limited Warranty
Top Page Image Contents