Poulan 421888 Snow Throwing Tips, To Start Engine, Before Stopping, If Recoil Starter has Frozen

Page 12

OPERATION

TO START ENGINE

•Be sure fuel shut-off valve is in the “OPEN” position. Your snow thrower engine is equipped with a recoil starter.

COLD START

1.Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps.

SNOW THROWING TIPS

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.

•It is easier and more efficient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Unfold Upper HandleInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BAR See FigCheck Engine OIL Level See Fig ADD Gasoline See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Service Notes Exploded KEY Part Description Auger Housing Scrapper BARAuger Bearing Bearing PlugAuger Assembly LH Auger Assembly RHKnob Black POP RivetWasher Plastic WasherLEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley PivotRepair Parts Snow Thrower - Model Number PR208 Handles Panel Bracket LH Panel Bracket RHHandle Grip Lower HandleSpacer RetainerKnob RED Handle KnobImpeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD Bottom01.10.001-B Console PanelRepair Parts Snow Thrower - Model Number PR208 Drive Speed Selector Assembly 43 402689 Drive Plate AssemblyEND Plate Control ARMAxle Shaft Roll PIN 3/16Sprocket Clik PINKEY Part Description LCT Engine Model PLMHK18600781DP 417014X428 Engine Mount PlateBelt Cover Traction BeltImpeller Belt Repair Parts Snow Thrower - Model Number PR208 Wheels Wheel Assembly LH187831X417 187866X417Repair Parts Snow Thrower - Model Number PR208 BAG of Parts Safety Ignition KEYRetainer PIN WrenchRepair Parts Snow Thrower - Model Number PR208 Decals Service Notes Service Notes Limited Warranty

421888 specifications

The Poulan 421888 is a powerful and versatile chainsaw designed for both professionals and hobbyists seeking reliability and performance in their cutting tasks. Renowned for its robust construction and ease of use, this model is particularly well-suited for a range of applications, from light trimming to more demanding tree felling and firewood preparation.

One of the standout features of the Poulan 421888 is its efficient engine. The chainsaw is equipped with a potent 42cc two-stroke engine that provides ample power for various cutting tasks while maintaining a lightweight design. This balance of power and weight allows users to operate the saw for extended periods without excessive fatigue. The engine also incorporates advanced technologies that contribute to optimal fuel efficiency, ensuring users can complete their work without constantly refueling.

Another notable characteristic of the Poulan 421888 is its easy-start mechanism. The innovative starting system reduces the effort required to fire up the engine, making it accessible for a broader range of users, including those who may be less experienced with chainsaws. Additionally, the chainsaw features an automatic oiler that ensures the chain remains adequately lubricated during operation, which extends the life of the chain bar and enhances cutting efficiency.

Safety is a paramount consideration in chainsaw design, and the Poulan 421888 addresses this with its comprehensive safety features. It comes equipped with a chain brake that stops the chain almost immediately in the event of a kickback, protecting the user from potential injuries. Furthermore, it includes a handguard and anti-vibration handles that improve comfort and stability while reducing operator fatigue.

The Poulan 421888 also places an emphasis on user-friendly maintenance. With its tool-less chain tensioning system, adjusting the chain for optimal tension is a quick and straightforward process, allowing users to focus on their work rather than wrestling with complex adjustments. The durable construction of the chainsaw ensures it can withstand the rigors of frequent use in various environments.

In summary, the Poulan 421888 is a well-rounded chainsaw that excels in providing power, efficiency, and safety. Its advanced features and user-centric design make it a reliable choice for anyone in need of a robust cutting tool, whether for professional landscaping, forestry work, or home improvement projects. With the Poulan 421888, users can tackle their cutting tasks with confidence and ease.
Top Page Image Contents