Poulan 421892 Meets A.N.S.I. Safety Requirements, Deflector remote control lever used to change

Page 9

OPERATION

SPARK

PLUG

SAFETY

IGNITION

KEY

CHOKE

CON-

TROL

THROTTLE

/ENGINE

CONTROL

RECOIL

STARTERPRIMER

HANDLE

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

ENGINE OIL CAP

AUGER

WITH DIPSTICK

CONTROL

 

LEVER

GASOLINE

FILLER CAP

CHUTE DEFLECTOR

FUEL

SHUT-OFF

VALVE

DISCHARGE

CHUTE

OIL DRAIN PLUG

CLEAN-OUT TOOL

FIG. 8

DISCHARGE CHUTE CONTROL LEVER

DRIVE SPEED

DEFLECTOR REMOTE

CONTROL LEVER

CONTROL LEVER

 

TRACTION

DRIVE

CONTROL

LEVER

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and

Throttle/engine control - used to select either FAST or

wrench.

SLOW engine speed and to STOP the engine.

Safety ignition key - must be inserted for the engine to

Traction drive control lever - used to engage power-pro-

start and run. Remove when snow thrower is not in use.

pelled forward or reverse motion of snow thrower.

Recoil starter handle - used for starting the engine.

Auger control lever - used to engage auger motion (throw

Primer - pumps additional fuel from the carburetor to the

snow).

Discharge chute control lever - used to change the di-

cylinder for use when starting a cold engine.

Choke control - used for starting a cold engine.

rection the snow is thrown.

 

Deflector remote control lever - used to change the

 

Skid plate - used to adjust height of scraper bar from the

 

ground.

distance the snow is thrown.

9

 

 

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents EXT RA Shear Bolts and Nuts Parts Packed Separately in CartonRotator Head Mounting Chute Deflecto R Remote Cont ROLHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Deflector remote control lever used to changeDischarge chute control lever used to change the di Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigBefore Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenMaintenance Engine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage Other TroubleshootingExploded KEY Part Description Auger Assembly LH Auger HousingAuger Assembly RH Scrapper BARBearing Plug Auger BearingPOP Rivet Knob BlackWasher Plastic WasherCable Assembly LEVER/CABLE Rotator AssemblyRotator Head Rotator Pivot BracketRetainer SpacerKnob RED Handle KnobHandle Grip Panel Bracket LH Panel Bracket RHLower Tube Pivot SupportTraction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD BottomConsole Panel 183352Drive Drive Plate Assembly Speed Selector AssemblyShoulder Screw END PlateRoll PIN 3/16 Axle ShaftSprocket Clik PINFrame Tecumseh Engine ModelEngine Mount Plate Belt CoverSafety Ignition KEY Wheel Assembly LH187831X421 187866X421DECAL, Poulan PRO, HP/24 DECAL, DangerDECAL, DANGER, Deflector DECAL, Poulan PROLimited Warranty
Top Page Image Contents