Poulan 421892 Install Traction Drive Control ROD See Figs, Install Auger Control ROD See Figs

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP OPEN-

ING DOWN

PIVOT

BRACKET

FIG. 3

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING
	TRACTION
	DRIVE
	CONTROL
	ROD
DRIVE
CONTROL
BRACKET

FIG. 4

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

6

Image 6

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Rotator Head Mounting Parts Packed Separately in CartonEXT RA Shear Bolts and Nuts Chute Deflecto R Remote Cont ROLRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Deflector remote control lever used to changeDischarge chute control lever used to change the di HOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine ADD Gasoline See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage Troubleshooting OtherExploded KEY Part Description Auger Assembly RH Auger HousingAuger Assembly LH Scrapper BARAuger Bearing Bearing PlugWasher Knob BlackPOP Rivet Plastic WasherRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Rotator Pivot BracketKnob RED SpacerRetainer Handle KnobLower Tube Panel Bracket LH Panel Bracket RHHandle Grip Pivot SupportShifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD Bottom183352 Console PanelDrive Shoulder Screw Speed Selector AssemblyDrive Plate Assembly END PlateSprocket Axle ShaftRoll PIN 3/16 Clik PINEngine Mount Plate Tecumseh Engine ModelFrame Belt Cover187831X421 Wheel Assembly LHSafety Ignition KEY 187866X421DECAL, DANGER, Deflector DECAL, DangerDECAL, Poulan PRO, HP/24 DECAL, Poulan PROLimited Warranty