Poulan 421104 owner manual Troubleshooting, Other

Page 19

STORAGE

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

TROUBLESHOOTING

See appropriate section in manual unless directed to a qualified service centre/department.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition switch OUT.

2.

Push safety ignition switch IN.

 

3.

Out of fuel.

3.

Fill fuel tank with fresh, clean gasoline.

 

4.

Throttle in STOP position.

4.

Move throttle to FAST position.

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

11.

Water in fuel.

11.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

4.

Water in fuel.

4.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

5.

Carburetor is in need of

5.

Contact a qualified service centre/department.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts. If vibration

vibration

 

augers or impeller.

 

remains, contact a qualified service centre/department.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact a qualified service centre/department.

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Storage Other TroubleshootingExploded KEY Part Description Auger 24 RH Auger HousingScrapper BAR Auger 24 LHBearing Plug Auger BearingPlastic Washer Knob BlackPOP Rivet WasherRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Rotator HeadHandle Knob SpacerRetainer Knob REDPivot Support Weldment Panel Bracket LH Panel Bracket RHHandle Grip Lower HandleShifter ROD Bottom Impeller ROD AssemblyTraction ROD Assembly Shifter ROD TOPConsole Panel Drive Control ARM Speed Selector Assembly43 420900 Drive Plate Assembly END PlateClik PIN Axle ShaftRoll PIN 3/16 SprocketBelt Cover Tecumseh Engine ModelFrame Engine Mount Plate187866X421 Wheel Assembly LHSafety Ignition KEY 187831X421DECAL, Poulan PRO DECAL, DangerDECAL, Poulan PRO, HP/24 DECAL, DANGER, DeflectorLimited Warranty

421104 specifications

The Poulan 421104 is a well-regarded chainsaw that has captured the attention of both casual users and professionals alike. Renowned for its reliability and robust performance, the Poulan 421104 is ideal for a myriad of tasks, including cutting firewood, clearing brush, and performing light to moderate tree trimming.

One of the main features of the Poulan 421104 is its powerful 42cc engine, which strikes a balance between efficiency and power. This engine is capable of delivering strong performance while remaining lightweight, making it user-friendly for extended periods. The chainsaw's gas-powered design allows for robust cutting power without the limitations that often come with electric saws, such as battery life.

The Poulan 421104 incorporates several technological advancements that enhance its usability. It features an easy-start system that reduces the effort needed to start the engine. This is particularly beneficial for users who may struggle with traditional pull-starts, ensuring a smoother experience right from the outset. The chainsaw is also equipped with an automatic oiling system, which continuously lubricates the chain during operation, ensuring minimal friction and efficient performance. This not only prolongs the life of the chain but also helps maintain optimal cutting efficiency.

Another notable characteristic is its reduced vibration technology. This feature minimizes vibrations transmitted to the user’s hands, ensuring greater comfort during use. This is particularly advantageous when working on more extensive jobs that require prolonged handling. The Poulan 421104 also features a 16-inch bar length that strikes a good balance between maneuverability and cutting capacity, allowing users to tackle a variety of cutting tasks with ease.

The chainsaw also boasts a chain brake feature, enhancing safety by allowing the user to stop the chain quickly in case of kickback or an emergency situation. The overall design of the Poulan 421104 prioritizes user safety, making it a suitable choice for both novices and seasoned users.

In summary, the Poulan 421104 is a versatile and reliable chainsaw, boasting a powerful engine, user-friendly features, advanced technologies, and enhanced safety mechanisms. It is designed for performance and durability, making it an excellent addition to any tool collection. Whether for professional landscaping or home maintenance, the Poulan 421104 proves to be a valuable asset for various cutting tasks.
Top Page Image Contents