Poulan P10530ESA Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or ad- justments:

1.Be sure throttle is in STOP position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute defl ector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the defl ector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 21)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shoulder/shear bolt and hex nut. Should a for- eign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Disconnect spark plug wire from spark plug and place it wear it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shoulder/shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Connect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

 

The impeller is secured to the impeller shaft with two (2)

 

capscrew/shear bolts and hex nuts. Should a foreign object

 

or ice become lodged in the impeller, the capscrews are

 

designed to break, preventing damage to any other com-

 

ponents. If impeller does not turn when auger control lever

 

is engaged, check to see if the capscrews have sheared.

 

To replace the capscrew/shear bolts:

16

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Disconnect spark plug wire from spark plug and place it wear it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Connect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

AUGER

AUGER

LOCKNUT

HUB

SHAFT

FIG. 21

TO REMOVE BELT COVER (See Fig. 22)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

 

BELT

 

COVER

FRAME

SCREWS

FIG. 22

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerTraining PreparationOperation Static Electricity HazardMaintenance and Storage API-SF-SJService and Adjustments Parts Packed Separately in Carton14-15 16-18Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Weight BAG See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Scraper BAR Before Starting the EngineTo Start Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Page KEY Part Description Page 183334 Knob, Lever Repair Parts Snow Thrower Model Number P10530ESA Handles Repair Parts Snow Thrower Model Number P10530ESA Handles Repair Parts Snow Thrower Model Number P10530ESA Drive Washer, Flat Page KEY Part Description Page KEY Part Description Limited Warranty

P10530ESA specifications

The Poulan P10530ESA is a robust and versatile outdoor power tool designed to meet the diverse needs of homeowners and landscape professionals alike. Known for its ease of use and reliability, this gas-powered string trimmer offers a range of features and technologies that make it an exceptional choice for tackling yard maintenance tasks.

At the heart of the Poulan P10530ESA is its powerful 30cc engine, which delivers impressive cutting performance while maintaining fuel efficiency. This engine is designed with a lightweight structure, making the trimmer easy to maneuver during extended use. The inclusion of a dual-line cutting head allows for more efficient trimming and enables users to cut larger swathes of grass in less time compared to single-line models.

One of the standout features of the P10530ESA is its easy-to-start technology. The trimmer is equipped with a primer bulb and a choke to ensure quick and effortless starting, even after long periods of storage. This user-friendly design is ideal for those who may not be experienced with gas-powered equipment, removing barriers to starting the trimmer and getting to work.

The Poulan P10530ESA also showcases a unique curved shaft design. This ergonomic feature provides enhanced comfort and reduces user fatigue, making it suitable for tasks that require precision cutting in tight spaces or difficult angles. Additionally, the handle of the trimmer is adjustable, allowing users to customize the height for better control and comfort during operation.

Another important characteristic of the P10530ESA is its durability. Built with high-quality materials, this trimmer is designed to withstand the rigors of regular use while maintaining reliable performance. The outer casing protects internal components from debris and damage, extending the trimmer's lifespan.

Moreover, the Poulan P10530ESA is compatible with various accessories, including brush cutters and edging attachments, making it a versatile tool for different landscaping needs. Its ability to easily switch between applications adds to its overall value and functionality for users.

In summary, the Poulan P10530ESA combines power, ease of use, and durability, making it an excellent investment for anyone looking to maintain their yard efficiently. With its advanced features and thoughtful design, this string trimmer is sure to provide exceptional performance, whether for occasional yard work or regular landscaping tasks.
Top Page Image Contents