Poulan 96192003100, PR1030ES owner manual To Remove Wheels See Fig, Carburetor, Engine Speed

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 23)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 23

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 24)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 24

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning Snow ThrowerEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH KEY Part DescriptionExploded Bearing Gearbox Assembly178675X008 Corner Bracket Clean OUT Tool Impeller PulleyAuger Bearing Bearing PlugChute Snow Shield Knob BlackPOP Rivet Shield Retainer StrapRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketRepair Parts Snow Thrower Model PR1030ES Handles Knob RED Repair Parts HandlesSpacer Handle KnobShifter ROD TOP Impeller RODTraction ROD Shifter ROD BottomPivot Support Wire HarnessLower Tube Console PanelRepair Parts Snow Thrower Model PR1030ES Drive Axle ShaftSprocket Repair Parts Snow Thrower Model PR1030ES 96192003100DRIVE Speed Selector AssemblyDrive Plate Assembly Rubber RingFrame Cover AssemblyComplete LCT Engine 427963X428Idler ARM Bracket Impeller BeltTraction Belt Idler PulleyRepair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket LH Cable Bracket RHSafety Ignition KEY Repair Parts Snow Thrower Model PR1030ES BAG of PartsPower Cord 198563DECAL, Danger Repair Parts Snow Thrower Model PR1030ES Decals181037 DECAL, DANGER, DeflectorLimited Warranty HOP

PR1030ES, 96192003100 specifications

The Poulan PR1030ES is a powerful tool in the realm of outdoor power equipment, particularly designed for homeowners and professionals seeking a reliable chainsaw. Engineered for efficiency and ease of use, this model stands out with its combination of advanced features and robust performance characteristics.

At the heart of the PR1030ES lies a dependable 30cc engine that delivers a strong performance while ensuring optimal fuel efficiency. This two-stroke engine is designed for cutting through a variety of materials, making it ideal for tasks ranging from light clearing to heavy-duty cutting. The chainsaw’s engine is complemented by an ergonomically designed handle that enhances user comfort during prolonged use, reducing fatigue and improving control.

One of the key features of the Poulan PR1030ES is its Easy Start technology, which allows for hassle-free ignition. This system minimizes the resistance felt during a pull start, making it easier for users to get the chainsaw running without excessive effort. The chainsaw also includes an automatic oiler, which delivers oil to the chain and bar continuously, ensuring smooth operation and extending the life of the tool.

The PR1030ES is equipped with a 12-inch bar and chain, striking a balance between compactness and cutting capability. This size is particularly effective for pruning, limbing, and cutting firewood, allowing users to maneuver easily and access tighter spaces during operation. Moreover, the chainsaw features a tool-less chain tensioning system, enabling quick adjustments and making it user-friendly for both seasoned professionals and novice users alike.

Another characteristic that enhances the chainsaw’s efficiency is its fuel system, which provides a reliable air-filtering mechanism to keep the engine clean and maintain optimal performance over time. The protective features include a safety throttle lock and a chain brake, ensuring that users can operate the chainsaw safely while minimizing risks associated with chain kickback.

In summary, the Poulan PR1030ES, model number 96192003100, combines a powerful engine with user-oriented design features for reliable and efficient operation. The key technologies such as Easy Start, automatic oiler, and tool-less chain adjustment make it a favorite among outdoor enthusiasts. With this chainsaw, users can expect a dependable tool capable of handling a variety of cutting tasks, suitable for both residential and light professional applications.
Top Page Image Contents