Poulan 96192003100 Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 20)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a spacer, shear bolt and hex nut. Should a foreign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever

is engaged, check to see if the capscrews have sheared. 16

To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 20

TO REMOVE BELT COVER (See Fig. 21)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

 

BELT

 

COVER

FRAME

SCREWS

FIG. 21

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Move Forward and Backward See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationSnow Thrower CleaningEngine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Auger Housing Auger Assembly 30 LHAuger Assembly 30 RH KEY Part DescriptionExploded Gearbox Assembly 178675X008 Corner Bracket Clean OUT ToolBearing Impeller PulleyAuger Bearing Bearing PlugKnob Black POP RivetChute Snow Shield Shield Retainer StrapLEVER/CABLE Rotator Assembly Cable Assembly AdjustableRotator Head Rotator Pivot BracketRepair Parts Snow Thrower Model PR1030ES Handles Repair Parts Handles SpacerKnob RED Handle KnobImpeller ROD Traction RODShifter ROD TOP Shifter ROD BottomWire Harness Lower TubePivot Support Console PanelAxle Shaft Repair Parts Snow Thrower Model PR1030ES DriveSprocket Repair Parts Snow Thrower Model PR1030ES 96192003100DRIVE Assembly Drive Plate AssemblySpeed Selector Rubber RingCover Assembly Complete LCT EngineFrame 427963X428Impeller Belt Traction BeltIdler ARM Bracket Idler PulleyRepair Parts Snow Thrower Model PR1030ES Wheels Cable Bracket LH Cable Bracket RHRepair Parts Snow Thrower Model PR1030ES BAG of Parts Power CordSafety Ignition KEY 198563Repair Parts Snow Thrower Model PR1030ES Decals 181037DECAL, Danger DECAL, DANGER, DeflectorLimited Warranty HOP

PR1030ES, 96192003100 specifications

The Poulan PR1030ES is a powerful tool in the realm of outdoor power equipment, particularly designed for homeowners and professionals seeking a reliable chainsaw. Engineered for efficiency and ease of use, this model stands out with its combination of advanced features and robust performance characteristics.

At the heart of the PR1030ES lies a dependable 30cc engine that delivers a strong performance while ensuring optimal fuel efficiency. This two-stroke engine is designed for cutting through a variety of materials, making it ideal for tasks ranging from light clearing to heavy-duty cutting. The chainsaw’s engine is complemented by an ergonomically designed handle that enhances user comfort during prolonged use, reducing fatigue and improving control.

One of the key features of the Poulan PR1030ES is its Easy Start technology, which allows for hassle-free ignition. This system minimizes the resistance felt during a pull start, making it easier for users to get the chainsaw running without excessive effort. The chainsaw also includes an automatic oiler, which delivers oil to the chain and bar continuously, ensuring smooth operation and extending the life of the tool.

The PR1030ES is equipped with a 12-inch bar and chain, striking a balance between compactness and cutting capability. This size is particularly effective for pruning, limbing, and cutting firewood, allowing users to maneuver easily and access tighter spaces during operation. Moreover, the chainsaw features a tool-less chain tensioning system, enabling quick adjustments and making it user-friendly for both seasoned professionals and novice users alike.

Another characteristic that enhances the chainsaw’s efficiency is its fuel system, which provides a reliable air-filtering mechanism to keep the engine clean and maintain optimal performance over time. The protective features include a safety throttle lock and a chain brake, ensuring that users can operate the chainsaw safely while minimizing risks associated with chain kickback.

In summary, the Poulan PR1030ES, model number 96192003100, combines a powerful engine with user-oriented design features for reliable and efficient operation. The key technologies such as Easy Start, automatic oiler, and tool-less chain adjustment make it a favorite among outdoor enthusiasts. With this chainsaw, users can expect a dependable tool capable of handling a variety of cutting tasks, suitable for both residential and light professional applications.
Top Page Image Contents