Poulan PR8527ES owner manual Engine, Cleaning

Page 14

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingWhen cleaning, repairing, or inspecting, make When traction drive control lever is engagedUsing the CLEAN-OUT Tool See Fig Stopped. Disconnect the spark plug wireTo Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes Limited Warranty

PR8527ES specifications

The Poulan PR8527ES is a robust and efficient gas-powered snow blower designed to tackle the challenges of winter weather with ease. Featuring a powerful 27-inch clearing width, this snow blower is ideal for homeowners with larger driveways and walkways, allowing them to clear snow quickly and effectively.

One of the standout features of the PR8527ES is its 250cc engine, which delivers reliable power and performance. The engine is equipped with an easy start system, ensuring that users can get their snow blower running on the first pull, even in cold weather conditions. This convenient feature minimizes the frustration often associated with starting gas-powered equipment in winter.

The PR8527ES boasts a heavy-duty steel construction, making it durable and capable of handling tough winter conditions. The auger system is designed to break down and move even heavy, wet snow, while the impeller quickly expels it away from the cleared path. The combination of a powerful auger and an efficient impeller allows users to clear snow up to 12 inches deep in a single pass, significantly reducing the time and effort needed for snow removal.

Another key characteristic of this snow blower is its adjustable chute, which allows users to control the direction of the snow discharge. The chute can throw snow up to 30 feet away, which is particularly beneficial for avoiding snow piles on sidewalks or driveways.

The PR8527ES is equipped with ergonomic controls, and the handles are designed to provide comfort during prolonged use. The snow blower features power steering, which is a valuable addition that enhances maneuverability, making it much easier to navigate around obstacles.

In terms of winter readiness, the PR8527ES includes LED headlights that illuminate the path ahead in low light conditions, providing safety and convenience for early morning or late-night snow clearing.

Overall, the Poulan PR8527ES is engineered for performance and user comfort, making it a reliable choice for anyone seeking to minimize the hassle of snow removal. Whether facing heavy snowfalls or light dustings, this snow blower stands ready to deliver dependable performance throughout the snowy season. Its combination of power, ease of use, and robust design positions it as a top choice for homeowners dealing with winter weather challenges.
Top Page Image Contents