Poulan PR8527ES owner manual To Remove Wheels See Fig

Page 16

SERVICE AND ADJUSTMENTS

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVETENSIONONTRACTIONDRIVEBELTIDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt must be fully seated in pulley groove when bringing

the snow thrower together.

16

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lock- washer and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

 

AUGER

SQUARE

 

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

 

 

AUGER PULLEY

 

 

 

 

BOLT

LOCK

 

 

 

WASHER

FRAME

AUGER

 

 

HOUSING

 

 

FIG. 21

TO REMOVE WHEELS (See Fig. 22)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN

OUTER HOLE

 

INNER

 

HOLE

WHEEL

WHEEL HUB

FIG. 22

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingWhen traction drive control lever is engaged Using the CLEAN-OUT Tool See FigWhen cleaning, repairing, or inspecting, make Stopped. Disconnect the spark plug wireScraper BAR Before Starting the EngineTo Start Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen Maintenance Cleaning EngineTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes Limited Warranty

PR8527ES specifications

The Poulan PR8527ES is a robust and efficient gas-powered snow blower designed to tackle the challenges of winter weather with ease. Featuring a powerful 27-inch clearing width, this snow blower is ideal for homeowners with larger driveways and walkways, allowing them to clear snow quickly and effectively.

One of the standout features of the PR8527ES is its 250cc engine, which delivers reliable power and performance. The engine is equipped with an easy start system, ensuring that users can get their snow blower running on the first pull, even in cold weather conditions. This convenient feature minimizes the frustration often associated with starting gas-powered equipment in winter.

The PR8527ES boasts a heavy-duty steel construction, making it durable and capable of handling tough winter conditions. The auger system is designed to break down and move even heavy, wet snow, while the impeller quickly expels it away from the cleared path. The combination of a powerful auger and an efficient impeller allows users to clear snow up to 12 inches deep in a single pass, significantly reducing the time and effort needed for snow removal.

Another key characteristic of this snow blower is its adjustable chute, which allows users to control the direction of the snow discharge. The chute can throw snow up to 30 feet away, which is particularly beneficial for avoiding snow piles on sidewalks or driveways.

The PR8527ES is equipped with ergonomic controls, and the handles are designed to provide comfort during prolonged use. The snow blower features power steering, which is a valuable addition that enhances maneuverability, making it much easier to navigate around obstacles.

In terms of winter readiness, the PR8527ES includes LED headlights that illuminate the path ahead in low light conditions, providing safety and convenience for early morning or late-night snow clearing.

Overall, the Poulan PR8527ES is engineered for performance and user comfort, making it a reliable choice for anyone seeking to minimize the hassle of snow removal. Whether facing heavy snowfalls or light dustings, this snow blower stands ready to deliver dependable performance throughout the snowy season. Its combination of power, ease of use, and robust design positions it as a top choice for homeowners dealing with winter weather challenges.
Top Page Image Contents