Poulan PR8527ESB owner manual HOW to USE Your Snow Thrower, Stopping

Page 10

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating 00155 your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

TO USE CHOKE CONTROL (See Fig. 11)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke, turn knob clockwise. Slowly turn knob counterclockwise to disengage.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

•Release the auger control lever to stop throwing snow.

ENGINE

1.Move throttle control to “STOP” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE FUEL SHUT-OFF VALVE (See Fig. 9)

The fuel shut-off valve is located beneath the fuel tank on the engine. Always operate the snow thrower with the fuel shut-off valve in the OPEN position.

OFF

OPEN

FIG. 9

TO USE THROTTLE CONTROL (See Fig. 10)

The throttle control is located on the engine.Always operate the snow thrower with the engine at full throttle. Full throttle offers the best snow thrower performance.

FAST

SLOW

FIG. 10

OFFFULL

FIG. 11

TO CONTROL SNOW DISCHARGE (See Figs. 12 & 13)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or au- ger become clogged, shut-off engine and wait for all moving parts to stop.Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

•To change the discharge chute position, press down- ward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

FIG. 12

The DISTANCE that snow is thrown is controlled by the position of the chute defl ector. Set the defl ector low to throw snow a short distance; set the defl ector higher to throw snow farther.

•To change the deflector position, loosen knob, move de-

10

flector to desired position and tighten knob securely.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model Number Snow ThrowerOperation TrainingPreparation Static Electricity HazardMaintenance and Storage API SG-SL14-15 Service and AdjustmentsParts Packed Separately in Carton 16-18Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Check Tire PressureOperation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingWhen cleaning, repairing, or inspecting, make When traction drive control lever is engagedUsing the CLEAN-OUT Tool See Fig Stopped. Disconnect the spark plug wireScraper BAR Before Starting the EngineTo Start Engine Before Stopping Snow Throwing TipsIf Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Limited Warranty
Top Page Image Contents