Poulan PP5524ESA owner manual Before Starting the Engine, Scraper BAR, To Start Engine

Page 12

OPERATION

TO ADJUST SKID PLATES (See Fig. 17)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the rear 1/2" hex nut only, then moving skid plate to desired position.Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION (LOW GROUND CLEARANCE)

AUGER

HOUSING

SKID PLATE

1/2" HEX NUT

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 17

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 18)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fi ll cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 18)

•Fill fuel tank to bottom of tank fi ller neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30

days to assure fuel freshness.

12

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CHOKE CONTROL

THROTTLE PRIMER ENGINE OIL

 

FILL CAP /

 

DIPSTICK

SAFETY

IGNITION

KEY

 

GASOLINE

 

FILLER CAP

 

FUEL SHUT-

 

OFF VALVE

RECOIL

STARTER BUTTON

STARTER

 

HANDLE

POWER CORD PLUG

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 18

TO START ENGINE

•Be sure fuel shut-off valve is in the OPEN position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Se- rious personal injury or damage to your snow thrower could result.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Number Snow ThrowerTraining PreparationOperation Static Electricity HazardMaintenance and Storage API-SF-SJService and Adjustments Parts Packed Separately in Carton14-15 16-18Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Weight BAG See FigCheck Tire Pressure Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Page KEY Part Description Page 183334 Knob, Lever Repair Parts Snow Thrower Model Number PP5524ESA Handles Repair Parts Snow Thrower Model Number PP5524ESA Handles Repair Parts Snow Thrower Model Number PP5524ESA Drive Washer, Flat 11 6 3452 KEY Part Description Page KEY Part Description Limited Warranty

PP5524ESA specifications

The Poulan PP5524ESA is a powerful and robust snow blower designed to tackle winter challenges with ease. This reliable machine is engineered for homeowners who need efficient snow clearing solutions for driveways, sidewalks, and patios. It combines user-friendly features with advanced technology to deliver outstanding performance and convenience.

One of the standout features of the PP5524ESA is its 24-inch clearing width, allowing it to handle large areas of snow quickly. The 5.5 horsepower engine delivers superior power, enabling the machine to cut through heavy and compacted snow with efficiency. Coupled with an auger and impeller system, the snow blower effectively collects and discharges snow up to 35 feet away, making it an ideal choice for heavy snow conditions.

The PP5524ESA is built with an electric start option, allowing users to start the machine easily with the push of a button, even in frigid temperatures where traditional pull starts can be a struggle. Additionally, the snow blower features six forward speeds and two reverse speeds, providing versatility and control over various snow types and conditions. This flexibility allows users to adjust their speed according to the terrain and snow depth, ensuring optimal performance.

The ergonomic design of the PP5524ESA contributes to user comfort. It is equipped with anti-vibration handles that reduce fatigue during extended use, making it easier to maneuver around obstacles. Furthermore, the adjustable chute control allows users to direct the snow discharge with precision, preventing unwanted snow accumulation on walkways and driveways.

Durability is a key characteristic of the Poulan PP5524ESA. The sturdy construction and high-quality materials ensure that it can withstand harsh winter weather and rigorous use year after year. The machine also features heavy-duty tires that provide excellent traction, helping it navigate through snow and uneven surfaces without getting stuck.

In summary, the Poulan PP5524ESA is a reliable and efficient snow blower equipped with a powerful engine, user-friendly features, and durable design. With its significant clearing width, adjustable speed settings, and advanced snow management technology, this snow blower is an essential tool for anyone dealing with heavy snowfall. Whether you're looking to keep your driveway clear or maintain a safe pathway, the PP5524ESA stands out as a practical and effective solution for winter snow removal.
Top Page Image Contents