Poulan PP1150E30 To Remove Wheels See Fig, To Adjust Cable Tension See Fig, Carburetor

Page 18

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 23)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL	OUTER HOLE
IN OUTER HOLE
OF AXLE ONLY)

AXLE

WHEEL

WHEEL HUB

FIG. 23

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

TO ADJUST CABLE TENSION (See Fig. 24)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 24

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

18

Image 18

Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To Control Snow Discharge See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Move Forward and Backward See Fig Before Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenMaintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Service Notes Exploded KEY Part Description Auger Assembly 30 RH Auger HousingAuger Assembly 30 LH Scrapper BARAuger Bearing Bearing PlugPlastic Washer Drift Cutter BARCARRIAGEBOLT5/16−18X.750 Lockwasher 5/16Shoulder Screw Knob BlackPOP Rivet Deflector SpringRotator Head LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator Pivot BracketLoop Handle RH Repair Parts Snow Thrower Model PP1150E30 HandlesLoop Handle LH Lower TubeTraction ROD 180480Impeller ROD RetainerHandle Knob SpacerKnob RED Washer 3/8Interlock CAM Wire HarnessInterlock Spring Torsion SpringAxle Shaft Repair PartsDrive SprocketRepair Parts Snow Thrower Model PP1150E30 Drive Speed Selector AssemblyDrive Plate Assembly Rubber Ring423185X428 Engine ModelFrame Engine Mounting PlateTraction Belt Cover AssemblyImpeller Belt Idler ARM BracketRepair Parts Snow Thrower Model PP1150E30 Wheels 01.06.005-A Safety Ignition KEY Repair Parts Snow Thrower Model PP1150E30 BAG of PartsPower Cord 198563DECAL, Danger Decals181037 DECAL, DANGER, DeflectorService Notes Service Notes Limited Warranty