Poulan PP1150E30 Using the CLEAN-OUT Tool See Fig, To Move Forward and Backward See Fig

Page 11

OPERATION

USING THE CLEAN-OUT TOOL (See Fig. 14)

In certain snow conditions, the discharge chute may be- come clogged with ice and snow. Use the clean-out tool to dislodge this blockage.

When cleaning, repairing, or inspecting, make certain all controls are disengaged and the au- ger/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent ac- cidental starting.

•Release the auger control lever and shut off the engine.

•Remove the clean-out tool from it's mounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage.

After the packed snow has been dislodged, return the clean- out tool to it's mounting clip by pushing it into the clip.

•Make sure the discharge chute is pointed in a safe direc- tion (no vehicles, buildings, people, or other objects are in the direction of discharge) before restarting the engine.

•Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger hous- ing and the discharge chute.

DISCHARGE CHUTE

CLEAN-OUT

TOOL

MOUNTING

CLIP

FIG. 14

TO MOVE FORWARD AND BACKWARD (See Fig. 15)

SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle.

•Squeeze traction drive control lever to handle to engage the drive system.

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

SPEED and DIRECTION are controlled by the drive speed control lever.

•Press downward on the speed control lever and move lever to desired position BEFORE engaging the trac- tion drive control lever. Be sure lever springs back and locks into desired position.

CAUTION: Do not move speed control lever when traction drive control lever is engaged. Damage to the snow thrower can result.

•Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower.

NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the discharge chute direction without interrupting the snow throwing process.

TRACTION DRIVE

CONTROL LEVER

DRIVE SPEED

CONTROL LEVER

FIG. 15

POWER STEERING OPERATION (See Fig. 16)

Steering triggers are used to assist in steering your snow thrower. The triggers are located on the underside of each handle. When a trigger is squeezed, it disen- gages the drive wheel on that side of snow thrower and allows it to turn in that direction.

•To turn left – squeeze left side trigger.

•To turn right – squeeze right side trigger.

LH TURN

RH TURN

TRIGGER

TRIGGER

FIG. 16

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Snow Thrower Model NumberSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo Control Snow Discharge See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Before Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingMaintenance Engine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Service Notes Exploded KEY Part Description Scrapper BAR Auger HousingAuger Assembly 30 LH Auger Assembly 30 RHBearing Plug Auger BearingLockwasher 5/16 Drift Cutter BARCARRIAGEBOLT5/16−18X.750 Plastic WasherDeflector Spring Knob BlackPOP Rivet Shoulder ScrewRotator Pivot Bracket LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Rotator HeadLower Tube Repair Parts Snow Thrower Model PP1150E30 HandlesLoop Handle LH Loop Handle RHRetainer 180480Impeller ROD Traction RODWasher 3/8 SpacerKnob RED Handle KnobTorsion Spring Wire HarnessInterlock Spring Interlock CAMSprocket Repair PartsDrive Axle ShaftRepair Parts Snow Thrower Model PP1150E30 Drive Rubber Ring AssemblyDrive Plate Assembly Speed SelectorEngine Mounting Plate Engine ModelFrame 423185X428Idler ARM Bracket Cover AssemblyImpeller Belt Traction BeltRepair Parts Snow Thrower Model PP1150E30 Wheels 01.06.005-A 198563 Repair Parts Snow Thrower Model PP1150E30 BAG of PartsPower Cord Safety Ignition KEYDECAL, DANGER, Deflector Decals181037 DECAL, DangerService Notes Service Notes Limited Warranty
Top Page Image Contents