Poulan PP1130ESC owner manual Assembly / Pre-Operation, INSTALL AUGER CONTROL ROD See Figs. 5 and

Page 6
INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

ASSEMBLY / PRE-OPERATION

TRACTION DRIVE

RETAINER

CONTROL LEVER

SPRING

INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)TRACTION

DRIVE

CONTROL

ROD

DRIVE

CONTROL

BRACKET

FIG. 4

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

AUGER

 

AUGER

CONTROL

RETAINER

CONTROL

ROD

LEVER

SPRING

 

 

AUGER

CONTROL

BRACKET

FIG. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotater head over chute bracket. If neces- sary, rotate chute assembly to align square and pin on un- derside of chute rotater head with holes in chute bracket.

3.With chute rotater head and chute bracket aligned, position chute rotater head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE

 

ROTATER

 

HEAD

3/8 LOCKNUT

 

3/8 WASHER

CHUTE

BRACKET

PIN

THREADED

STUD

ROTATER HEAD

MOUNTING

BRACKET

FIG. 7

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents IMPORTANT MANUAL OWNERS MANUAL MODEL NUMBERSNOW THROWER PP1130ESCTRAINING SAFETY RULESSafe Operation Practices for Snow Throwers PREPARATIONMAINTENANCE AND STORAGE PRODUCT SPECIFICATIONSCUSTOMER RESPONSIBILITIES SAFETY RULES PARTS PACKED SEPARATELY IN CARTONSERVICE AND ADJUSTMENTS PRODUCT SPECIFICATIONSREMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and INSTALL WEIGHT BAR See FigCHECK TIRE PRESSURE OPERATION KNOW YOUR SNOW THROWERElectric start button - used for starting the engine MEETS A.N.S.I. SAFETY REQUIREMENTSToolbox - to store spare shear bolts, locknuts & wrench Choke Control - used for starting a cold engineTO USE FUEL SHUT-OFF VALVE See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE THROTTLE CONTROL See FigTO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO MOVE FORWARD AND BACKWARD See FigSCRAPER BAR BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig CHECK ENGINE OIL LEVEL See FigSNOW THROWING TIPS BEFORE STOPPINGIF RECOIL STARTER HAS FROZEN BEFORE EACH USE MAINTENANCEGENERAL RECOMMENDATIONS LUBRICATIONV-BELTS CLEANINGENGINE AUGER GEAR CASETO ADJUST SNOW THROWER HEIGHT SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key CHUTE DEFLECTORTO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig STORAGEOTHER CARBURETORDoes not start TROUBLESHOOTINGLoss of power Engine idles orLIMITED WARRANTY
Top Page Image Contents