Poulan PP1130ESC Assembly / Pre-Operation, INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and

Page 7

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt, 5/16 ﬂ at washer and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deﬂ ector with 1/4-20 shoulder bolt, 1/4 ﬂ at washer and 1/4-20 locknut as shown. Tighten securely.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deﬂector as shown.

	CHUTE	SPRING	1/4-20
	DEFLECTOR		SHOULDER
	CABLE		BOLT
	CABLE
	EYELET	HOOK BETWEEN
	1/4 FLAT	HOOK BETWEEN
	1/4 FLAT		HEX NUTS
	WASHER		ON CHUTE
	1/4-20	ROTATER HEAD
	1/4-20
	LOCK-
	NUT		5/16-18
			CARRIAGE
			BOLT
	REMOTE
	CABLE
	BRACKET
	5/16 FLAT
	WASHER
	5/16-18
	LOCKNUT

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

INSTALL WEIGHT BAR (See Fig. 10)

Though seldom required, the weight bar will reduce the tendency of the auger housing to ride up on hard, icy drifts. Should conditions require it, install as follows:

1.Shut off engine and wait for all moving parts to stop.

2.Secure weight bar to auger housing with carriage bolts and hex nuts as shown. Tighten securely.

WEIGHT	CARRIAGE
BAR	BOLTS
	HEX NUTS
	AUGER HOUSING
	FIG.10

CHECK TIRE PRESSURE

The tires on your snow thrower were overinﬂated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14–17 PSI.

7

Image 7

Contents PP1130ESC OWNERS MANUAL MODEL NUMBERSNOW THROWER IMPORTANT MANUALPREPARATION SAFETY RULESSafe Operation Practices for Snow Throwers TRAININGPRODUCT SPECIFICATIONS MAINTENANCE AND STORAGECUSTOMER RESPONSIBILITIES PRODUCT SPECIFICATIONS PARTS PACKED SEPARATELY IN CARTONSERVICE AND ADJUSTMENTS SAFETY RULESINSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See Fig INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL WEIGHT BAR See Fig INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 andCHECK TIRE PRESSURE KNOW YOUR SNOW THROWER OPERATIONChoke Control - used for starting a cold engine MEETS A.N.S.I. SAFETY REQUIREMENTSToolbox - to store spare shear bolts, locknuts & wrench Electric start button - used for starting the engineTO USE THROTTLE CONTROL See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE FUEL SHUT-OFF VALVE See FigTO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO THROW SNOW See FigCHECK ENGINE OIL LEVEL See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BARBEFORE STOPPING SNOW THROWING TIPSIF RECOIL STARTER HAS FROZEN LUBRICATION MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEAUGER GEAR CASE CLEANINGENGINE V-BELTSCHUTE DEFLECTOR SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig CARBURETOR STORAGEOTHER TO REMOVE WHEELS See FigEngine idles or TROUBLESHOOTINGLoss of power Does not startLIMITED WARRANTY