MTD 769-01275D warranty Friction Wheel Removal

Page 17

1

2

3

Friction Wheel Removal

If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjust- ment on page 14 fails to correct the problem, the friction wheel may need to be replaced. Follow the instructions below. Examine the friction wheel for signs of wear or cracking and replace if necessary

•Place the shift lever in third Forward (F3) position.

•Drain the gasoline from the snow thrower, or place a piece of plastic under the gas cap.

•Carefully pivot the snow thrower up and forward so that it rests on the auger housing.

1.a. Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it.

b.Remove the right-hand wheel by removing the screw and bell washer which secure it to the axle.

2.Carefully remove the hex nut and washer which secures the hex shaft to the snow thrower frame and lightly tap the shaft’s end to dislodge the ball bearing from the right side of the frame.

3.Carefully position the hex shaft downward and to the left before carefully sliding the friction wheel assembly off the shaft.

NOTE: If you’re replacing the friction wheel assembly as a whole, discard the worn part and slide the new part onto the hex shaft. Follow the steps above in reverse order to reassemble components. If you’re disassem- bling the friction wheel and replacing only the rubber ring, proceed as follows:

4.Remove the four screws which secure the friction wheel’s side plates together.

•Remove the rubber ring from between the plates.

•Reassemble the side plates with a new rubber ring.

•Slide the friction wheel assembly back onto the hex shaft and follow the steps above in reverse order to reassemble components.

4

5

Maintaining

Your Snow

Thrower

When reassembling the friction wheel as- sembly, tighten each screw only one rota- tion before turning the wheel clockwise and proceeding with the next screw. Repeat this process several times to ensure the plates are secured with equal force.

NEVER replace the auger shear pins with anything other than OEM Part No.738-04124 replacement shear pins. Any damage to the auger gearbox or other components as a result of failing to do so will NOT be covered by your snow thrower’s warranty.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents MTD LLC, P.O. BOX 361131 CLEVELAND, Ohio Two-Stage Snow Thrower E, F StyleCustomer Support Table of ContentsFinding and Recording Model Number 53% %842! #!54/ %. /0%2!4 Your Responsibility%, 352&!#%3  2%!$ /0%2!4/2g3 -!.5!,Your Responsibility Restrict the use TrainingPreparationOperation Maintenance & StorageDo not modify engine Your ResponsibilityPosition the chute assembly over the base Setting Up Your Snow ThrowerSkid Shoes Auger ControlTire Pressure Chute directional controlKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Stopping The Engine Gas & Oil Fill-UpIf your home’s Electric StarterTo Engage Drive Chute Clean-Out ToolTo Engage Augers Auger Control TestDrive Control Making AdjustmentsShift Cable To adjust the skid shoes Chute Bracket AdjustmentEngine Maintaining Your Snow ThrowerLubrication Shave Plate and Skid ShoesAuger Belt Replacement Drive Belt Replacement Friction Wheel Removal Preparing Engine Off-Season StoragePreparing Snow Thrower Short-Term StorageProblem Cause Remedy Trouble ShootingStyles E & F To order replacement Parts, call Or visit us on Web at Illustrated Parts List            790-00209 67 70 17 9 684-04153 Page Page MANUFACTURER’S Limited Warranty for

769-01275D specifications

The MTD 769-01275D is an outstanding model in the realm of outdoor power equipment, particularly recognized for its performance and reliability in lawn care and maintenance. Engineered by MTD Products, a company with a rich heritage in manufacturing outdoor power tools, this model combines advanced technologies with user-friendly features, making it a top choice for both homeowners and landscaping professionals alike.

One of the main features of the MTD 769-01275D is its powerful engine. Designed to deliver efficient operation, the engine provides ample torque and speed, enabling the machine to tackle various types of terrain and grass densities. Its robust construction promises durability, ensuring that the equipment can withstand rigorous use throughout the season.

The MTD 769-01275D is equipped with an innovative cutting system that enhances its performance. With adjustable cutting heights, users can customize the mower to achieve the desired grass length, whether for a well-manicured lawn or a natural look. This versatility is further complemented by sharp, high-quality blades that promote clean cuts, resulting in healthier grass growth and an aesthetically pleasing yard.

A standout characteristic of the MTD 769-01275D is its ergonomic design. The handle is designed for comfort and ease of use, reducing fatigue during extended periods of operation. Additionally, the intuitive controls allow users to navigate various settings without complications, making the mowing experience more enjoyable and efficient.

Technologically, the MTD 769-01275D incorporates features such as easy-start mechanisms, and some models may include electric start options, allowing for quick and hassle-free ignition. Fuel efficiency is another significant aspect, with the engine designed to consume less fuel while providing maximum power.

Another commendable feature is the design of the deck. The wide cutting deck allows for more extensive cutting swath, significantly reducing the time spent mowing. It is also designed to be lightweight, making it easier to maneuver around obstacles in the yard.

Overall, the MTD 769-01275D stands out for its combination of power, convenience, and innovative features. Whether for residential use or professional landscaping, it represents an excellent investment for those looking to maintain their outdoor spaces effectively. Its blend of efficiency, durability, and user-centric design makes it a desirable option among outdoor power equipment.
Top Page Image Contents