Simplicity 7/22E manual Englne Puiioy Drve bel, G u r e 1 2 . D r i v e C o n t r o l S p r i n g

Page 16

Adjusting Drive Belts

If the auger or wheels slip under load, belts could be stretched or worn. Adjust as follows:

1.Remove the belt cover (figure 10). Determine which belt requires adjustment.

2.Loosen the locknut on the appropriate idler pulley and move the idler pulley i/4” toward the belt (figure 11). Tighten the locknut.

3.Re-install the belt cover.

4.Determine if additional adjustment is required by try- ing the unit. Repeat step 1 - 3 if necessary.

NOTE: If auger or wheels continue to slip after adjust- ing the idler pulleys, the spring (figure 12) on either con- trol rod might be stretched and worn and require replace- ment. Replace either the auger control rod spring or drive control rod spring as necessary, then repeat steps I-4.

Adjusting Belt Guides

Check each belt guide for proper clearance using the fol- lowing procedure.

NOTE: Belt guides on 7 HP mode/s are slight//y different than shown, but adjustment is the same.

I. Remove the belt cover (figure IO).

2.Have someone hold both the auger and drive clutch levers tight against the handgrips (figure 12).

3.Loosen the screw securing the belt guide (figure 11). Adjust the guide so it clears the belt by l/16” - l/8”. The clearance should be equal on both side of the pulley. Tighten the screw securely.

NOTE: When adjusting the right belt guide, make sure guide does not contact the pulley hub.

4. Re-install the belt cover.

Replacing Drive Belts

The drive belts on this snowthrower are of special con- struction and should be replaced with original equipment belts available from your dealer. See COMMON REPLACEMENT PARTS at the back of tfiis.manual for part numbers.

Use the following procedure to replace either drive belt.

1.Remove gas from fuel tank and run engine until it stops running from lack of fuel.

2.Disconnect spark plug wire and fasten it away from the spark plug.

3.Remove belt cover (figure 10).

Englne PUIIOY 01

dr;ve bel;

\

‘gure 1 1 . D r i v e B e l t s a n d P u l l e y s - B e l t C o v e r O f f

F i g u r e 1 2 . D r i v e C o n t r o l S p r i n g

4.Loosen the screw securing the belt guide (figure 11). Pivot the belt guide as necessary and remove the drive belt from the pulley.

5.Stand the snowthrower up onto the auger end.

1 2

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 55cd22 BakerTM II 500 N. Spring Street, P.O. Box 997 Port Washinnton, WI Page Table Of Contents Safety Rules GeneralPreparation OperationMaintenance & Storage SafetydecalsSnowthrower Controls Engine ControlsEngine Speed Ground SpeedScraper BAR & Skid Shoes DeflectorG u r e 4 . S k i d S h o e a d j u s t m e n t Checks Before Each START-UP Operation on SlopesStarting the Engine Operating the Snowthrower After Each USEOr fuel tank, in a heated shelter or in enclosed U s e a n e x p l o s i o nNormal Care OFF-SEASON StorageCheck Auger Gear Case Lubrication Starting After StorageLubrication Regular- MaintenanceChecking Tire Pressure Troubleshooting Drive Belts Shift Control AdjustmentG u r e 9 . S h i f t C o n t r o l a d j u s t m e n t Englne Puiioy Drve bel G u r e 1 2 . D r i v e C o n t r o l S p r i n gShear PIN Replacement Roller Chain ReplacementA n d o n e n d Wheel Axle Bearing Replacement Auger Shaft Bearing ReplacementMust be used on each side of the shaft G u r e 1 6 . W h e e l a n d a u g e r B e a r i n g sSpecifications Accessories Common Replacement PartsTechnical Manual Availability

1691414, 7/22E, 1691411, 1691413 specifications

Simplicity 1691413, 1691411, 7/22E, and 1691414 are a series of innovative devices designed to enhance performance and streamline user experience across various applications. Built for efficiency, these models embody the principles of simplicity and functionality, aiming to cater to both individual and professional needs.

One of the main features of the Simplicity lineup is its emphasis on user-friendly interfaces. Each model has been designed with clear navigation and accessible controls, allowing users to operate the devices with minimal training. This focus on usability makes these devices suitable for a wide range of users, from novices to seasoned professionals.

In terms of technology, the Simplicity series is equipped with advanced processing capabilities that ensure quick responses and seamless performance. The inclusion of state-of-the-art processors allows these models to handle complex tasks without lag. Additionally, they feature high-resolution displays that provide crisp visuals, enhancing user interaction.

Connectivity is another key characteristic of the Simplicity models. With built-in Wi-Fi, Bluetooth, and other communication protocols, users can easily connect to a variety of devices and networks. This feature not only facilitates data transfer but also allows for remote operation and monitoring, making it a versatile option for both home and business environments.

Simplicity 1691413, 1691411, 7/22E, and 1691414 also prioritize energy efficiency. These models incorporate technologies that reduce power consumption without compromising performance, making them eco-friendly choices. This focus on sustainability resonates with modern users seeking to reduce their carbon footprint.

Furthermore, durability is an essential aspect of the Simplicity range. Constructed with robust materials, the devices are designed to withstand daily wear and tear, making them a reliable choice for various settings. This resilience is complemented by extensive warranties, ensuring users have peace of mind.

Overall, the Simplicity 1691413, 1691411, 7/22E, and 1691414 models exemplify the perfect balance between simplicity, functionality, and technology. Their innovative features, robust performance, and eco-friendly designs make them standout options in a competitive market. Whether for personal use or professional applications, these devices are tailored to meet diverse user needs efficiently and effectively.
Top Page Image Contents