MTD 640 manual Trouble Shooting Guide, OFF-SEASON Storage

Page 14

SECTION 8: OFF-SEASON STORAGE

WARNING: Never store engine with fuel in tank indoors or in enclosed, poorly ventilated areas where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer, or other gas appliance.

If unit is to be stored over 30 days, prepare the engine for storage following instructions in the engine manual.

Remove all dirt from exterior of engine and equipment.

Follow lubrication recommendations on page 11.

NOTE: When storing any type of power equipment in an poorly ventilated or metal storage shed, care should be taken to rustproof the equipment, especially springs, cables and all moving parts.

SECTION 9: TROUBLE SHOOTING GUIDE

Trouble

Possible Cause(s)

Corrective Action

Engine fails to start

Fuel tank empty, or stale fuel.

Fill tank with clean, fresh gasoline. Fuel may not last over thirty days

 

 

unless a fuel stabilizer is used.

 

Blocked fuel line.

Clean fuel line.

 

Choke not in ON position

Move switch to ON position

 

Faulty spark plug.

Clean, adjust gap or replace.

 

Key not in switch on engine.

Insert key.

 

Spark plug wire

Connect spark plug wire.

 

disconnected.

 

 

Primer button not depressed.

Refer to the engine manual packed with your unit.

 

Fuel shut-off valve closed

Open fuel shut-off valve.

 

(if so equipped).

 

Engine runs erratic

Unit running on CHOKE.

Move choke lever to OFF position.

 

Blocked fuel line or stale fuel.

Clean fuel line; fill tank with clean fresh gasoline. Fuel may not last

 

 

over thirty days unless a fuel stabilizer is used.

 

Water or dirt in fuel system.

Drain fuel tank. Refill with fresh fuel.

 

Carburetor out of adjustment.

Refer to the engine manual packed with your unit or have carburetor

 

 

adjusted by an authorized service dealer.

Loss of power

Spark plug wire loose.

Connect and tighten spark plug wire.

 

Gas cap vent hole plugged.

Remove ice and snow from cap. Be certain vent hole is clear.

 

Exhaust port plugged.

Clean-see Maintenance section of engine manual.

Engine overheats

Carburetor not adjusted

Refer to the engine manual packed with your unit or have carburetor

 

properly.

adjusted by an authorized service dealer.

 

Incorrect fuel mixture.

Drain fuel tank. Refill with proper fuel mixture.

Excessive vibration

Loose parts or damaged auger.

Stop engine immediately and disconnect spark plug wire. Tighten all

 

 

bolts and nuts. Make all necessary repairs. If vibration continues, have

 

 

unit serviced by an authorized service dealer.

Unit fails to propel

Incorrect adjustment of drive

Adjust drive cable. Refer to Adjustment section of this manual.

itself

cable.

 

 

Drive belt loose or damaged.

Replace drive belt. Refer to Belt Replacement on page 12.

Unit fails to

Discharge chute clogged.

Stop engine immediately and disconnect spark plug wire. Clean dis-

discharge snow

 

charge chute and inside of auger housing.

 

Foreign object lodged in auger.

Stop engine immediately and disconnect spark plug wire. Remove

 

Incorrect adjustment of drive

object from auger.

 

cable.

Adjust drive cable. Refer to Adjustment section of this manual.

 

Drive belt loose or damaged.

Replace drive belt. Refer to Belt Replacement on page 12.

 

Shear bolt(s) sheared

Replace shear bolt(s)

NOTE: For repairs beyond the minor adjustments listed above, contact your nearest authorized service dealer or call 1-800-800-7310 for the Customer Support Center. Refer to separate engine manual packed with your snow thrower for more engine related information.

14

Image 14
Contents OPERATOR’S Manual Table of Contents Preparation Important Safe Operation PracticesTraining OperationMaintenance and Storage Your ResponsibilityAssembling Your Snow Thrower Tire Pressure Pneumatic Tires Final AdjustmentsSkid Shoes Auger ControlKnow Your Snow Thrower Operating ControlsGas And Oil Fill-up Operating Your Snow ThrowerBefore Starting Starting EngineMaking Adjustments Drive Wheels Auger ControlShift Rod Maintaining Your Snow Thrower LubricationAugers Belt ReplacementServicing Your Snow Thrower Shave Plate and Skid ShoesChanging Friction Wheel Rubber Drive BeltTrouble Shooting Guide OFF-SEASON StorageParts List for Model Part DescriptionModel Model Drive Clutch Cable Auger Clutch Wheels Wheel Assemblies Model Size 710-1652 Hex Washer Screw 1/4-20 x 3830 Your Notes Your Notes MANUFACTURER’S Limited Warranty