MTD 31AH5C3F401 Maintaining Your Snow Thrower, Drive Wheels, Skid Shoe Adjustment, Lubrication

Page 11

Reconnect the upper shift rod to the lower shift rod by reinserting the hairpin clip removed earlier and sliding the shift rod connector back down into place.

IMPORTANT: Make certain to check for correct adjustment of the shift rod as instructed under Final Adjustments in the Assembly Section, before operating the snow thrower.

Drive Wheels

The wheels may be adjusted for two different methods of operation. The adjustment is made by placing the click pins in one of two different holes on the right side of the unit. See Figure 10.

One Wheel Driving: Insert the click pin only through the outside hole of the axle (NOT the rim) on the right side of the snow thrower. This position gives power drive to the left wheel only, making the unit easier to maneuver.

Both Wheels Driving: Insert the click pin through the hole in the hub of the rim and the INSIDE hole on the snow thrower’s right axle. This position is good for heavy snow as there is power drive in both wheels.

IMPORTANT: NEVER operate the snow thrower with the click pin inserted through both the RIM and the OUTSIDE HOLE in the axle. Doing so can result in serious damage to the drive system.

Inside Hole

In Axle

Click Pin In

Outside Hole

Figure 10

Skid Shoe Adjustment

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes. Refer to Skid Shoe Adjustment in the Assembly Section.

Auger Control Adjustment

Refer to the information found under Final Adjustments in the Assembly Section to adjust the auger control.

SECTION 6: MAINTAINING YOUR SNOW THROWER

WARNING: Before lubricating, repairing, or inspecting, disengage all clutch levers and stop engine. Wait until all moving parts have come to a complete stop. Disconnect spark plug wire and ground it against the engine to prevent unintended starting.

Lubrication

Engine

Refer to the separate engine manual packed with your unit for all engine lubrication instructions.

IMPORTANT: When following instructions in separate engine manual for draining oil, be sure to protect frame to avoid oil dripping onto transmission parts.

Gear Shaft

Lubricate the gear shaft with 6-n-1 grease at least once a season or after every 25 hours of operation (available at automotive stores, or order part number 737-0170).

Refer to Figure 8.

IMPORTANT: Keep all grease and oil off of the rubber friction wheel and aluminum drive plate.

Drive and Shifting Mechanism

Lubricate at least once a season or after every 25 hours of operation. Remove the rear cover, lubricate any chains, sprockets, gears, bearings, shafts, and shifting mechanism at least once a season. Use engine oil or a spray lubricant. Avoid getting oil on the friction wheel rubber and aluminum drive plate. Refer to Figure 8.

There is a grease fitting on the top of the axle shaft which drives the rear track drive wheels on both sides of the unit. Grease these fittings every 25 hours or once a season.

Traction Control / Auger Control Lock

The cams on the ends of the control rods which interlock the traction drive and auger drive controls must be lubricated at least once a season or every 25 hours of operation. The cams can be accessed beneath the handle panel. Use a multi-purpose automotive grease.

Electric Chute-Rotation Motor

The gear on the electric chute-rotation motor and the base of the discharge chute itself should be lubed with multi-purpose automotive grease once a season. See Figure 11.

11

Image 11
Contents OPERATOR’S Manual Table of Contents Operation Important Safe Operation PracticesTraining PreparationMaintenance And Storage Loose Parts AssemblyAssembling Your Snow Thrower UnpackingTraction Control and Shift Lever Adjustment Final AdjustmentsAuger Control Adjustment Skid Shoe AdjustmentSkid Shoe Know Your Snow ThrowerChute Tilt Control Auger Drive ControlOperating Your Snow Thrower To Engage Augers Recoil StarterTo Stop Engine To Engage Wheel DriveShift Rod Adjustment Chute Assembly AdjustmentTraction Control Adjustment Drive Wheels Skid Shoe AdjustmentAuger Control Adjustment Maintaining Your Snow ThrowerAugers Belt Removal And ReplacementServicing Your Snow Thrower EngineDrive Belt Replacing Friction Wheel RubberOff-season Storage Problem Cause Remedy Trouble ShootingPage Part Description Models H5C3F & H5Q3GFor Reference Only 746-0901 Control Cable Models H5C3F & H5Q3G Carriage Bolt, 5/16-18 x Models H5C3F & H5Q3G Flat Washer 3/8 x 1.25 OD Models H5C3F & H5Q3G Dogg Assembly RH Dogg Assembly LH 618-0575 Page Page MANUFACTURER’S Limited Warranty for

31AH5C3F401, 31AH5Q3G401 specifications

The MTD 31AH5Q3G401 and MTD 31AH5C3F401 are advanced power MOSFETs designed for various high-efficiency applications. These components are notable for their superior performance in energy conversion and management, making them ideal for use in automotive, industrial, and consumer electronics sectors.

One of the main features of the MTD 31AH5Q3G401 is its low on-resistance (Rds(on)), which significantly contributes to enhanced energy efficiency. Low Rds(on) translates to lower conduction losses during operation, leading to reduced heat generation. This characteristic is crucial in applications where thermal management is a concern, allowing designers to minimize the size of heat sinks and cooling systems.

The MTD 31AH5C3F401 complements this with a fast switching speed, which is essential for high-frequency applications such as switch-mode power supplies (SMPS) and DC-DC converters. The rapid transition from on to off state results in decreased switching losses, allowing for higher overall efficiency in power conversion processes.

Both models utilize a robust silicon technology that enhances their reliability and durability under various operational conditions. Their maximum voltage ratings can easily accommodate voltage transients encountered in automotive applications, ensuring they can handle high-stress environments without compromising performance.

In terms of packaging, the MTD 31AH5Q3G401 and 31AH5C3F401 are available in compact forms, enabling designers to save space on PCBs while maintaining a high power density. The integration of thermal management features within the package reduces thermal resistance, further aiding in effective heat dissipation, which is critical in prolonged use.

A common characteristic of both devices is their ability to operate in a wide range of temperatures, which makes them suitable for both outdoor and indoor applications. They are capable of delivering reliable performance across different environmental conditions, enhancing their usability in various sectors.

In summary, the MTD 31AH5Q3G401 and 31AH5C3F401 are exemplary components featuring low on-resistance, fast switching capabilities, robust silicon technology, and compact packaging. These attributes position them as ideal choices for designers looking to enhance the efficiency and reliability of their electronic systems while managing thermal challenges effectively. With their versatility and strong performance metrics, these MOSFETs are set to play a vital role in the future of power electronics.