Snapper SMI I924RX MS B&S 24 (CE), SMI I924EX B&S 24 (CE) manual Operation, Starting the Engine

Page 16

Operation

Operation

STARTING THE ENGINE

1.Check the oil level. See the Engine Manual How to Check/Add Oil section

2.Make sure equipment drive controls are disengaged.

3.Push the stop switch to the on position (A, Figure 3).

A

Figure 3. On/Stop Switch

A.On/Stop Switch Selector

4.Insert the engine key (A, Figure 4) into the engine key slot and push fully in to the RUN position.

5.Turn the choke knob (B) fully clockwise if engine is cold.

Note: Do not use the choke to start a warm engine.

6. Push the primer button (C) two times.

Note: Do not use the primer to start a warm engine.

C

B

A

Figure 4. Safety Key, Choke, and Primer Button

A.Safety Key

B.Choke Control Knob

C.Primer Button

7.Rewind Start: Firmly hold the starter cord handle (A, Figure 5). Pull the starter cord handle slowly until resistance is felt, then pull rapidly.

WARNING

Rapid retraction of the starter cord (kickback) will pull your hand and arm toward the engine faster than you can let go. Broken bones, fractures, bruises or sprains could result. When starting engine, pull the starter cord slowly until resistance is felt and then pull rapidly to avoid kickback.

A

Figure 5. Rewind Start

A. Starter Cord Handle

Note: If the engine does not start after three attempts, see the Engine Manual Troubleshooting section.

8.Electric Start: First connect the extension cord to the power cord receptacle and then into a wall receptacle. If additional extension cord is required, make sure it is 3-wire.

WARNING

If the extension cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person to avoid to avoid a hazard.

9. Electric Start: Depress the push button (A, Figure 6). After you start the engine, first disconnect the extension cord from the wall receptacle and then from the power cord receptacle (B).

A

B

Figure 6. Electric Start

A.Starter Push Button

B.Power Cord Receptacle

CAUTION

To extend the life of the starter, use short starting cycles (five seconds maximum.) Wait one minute between starting cycles.

Note: If the engine does not start after three attempts, see the Engine Manual Troubleshooting section.

16

Image 16
Contents Mfg. No Description Manual Part NoSafety Icons Safety DecalsRead the Manual Table of Contents Read the Manual Safety Rules & Information Operating SafetyChildren Fuel and Maintenance Safety Rules and InformationMoving Parts Thrown ObjectsSafety Rules & Information TrainingSafety Rules and Information Decals DecalsNorth American Model Decals Decals ALL Model DecalsCE Model Decals Part No SMI/SNAPPER Speed Control Decal, All ModelsSafety Icons Safety IconsIdentification Numbers Product Identification NumbersCE Identification TAG Markings North American / CE Models CE Models OnlyFeatures & Controls Control LocationsSpeed Selector Auger ControlFeatures & Controls Operation Checks Before Each START-UPElectric Start Starting ControlsManual Start Operation Starting the EngineStopping the Engine Operating the SnowthrowerGround Speed Selector Engine SpeedWhen Pushing the Snowthrower DeflectorScraper BAR & Skid Shoes Traction Drive LockAfter Each USE Clearing a Clogged Discharge ChuteStorage Regular Maintenance Maintenance ScheduleChecking Tire Pressure Auger Gear Case LubricationRegular Maintenance LubricationCheck / Lubricate Linkage Lubricating the Auger Shaft AssemblyLubricate as shown in figure Maintenance Troubleshooting TroubleshootingAuger does not stop when auger Auger rotates, but snow is notThrown far enough Poor tractionAdjustments Auger Drive AdjustmentTraction Drive Adjustment Initial AdjustmentRun-In Adjustment Adjustments10.95cm Auger Drive Belt Belt AdjustmentTraction Drive Belt Belt Guide Adjustment Shear PIN Replacement3.18mm Service Belt ReplacementRotator Shaft Removal Pin, Hair Traction Drive Belt Traction Belt Change Swing Plate Alignment Tabs Service Specifications DimensionsEngine ChassisSpecifications Maintenance Items Replacement PartsTechnical Manuals O D U C T S

SMI I924RX MS B&S 24 (CE), SMI I924E B&S 24, SNP I924RX MS B&S 24 (CE), SMI I924EX B&S 24 (CE), SNP I924EX B&S 24 (CE) specifications

Snapper has established itself as a leading name in the lawn care and outdoor equipment industry, offering a range of advanced and reliable products designed for efficiency and longevity. Within this offering, several models stand out: the Snapper SNP I924E B&S 24 (CE), SNP I924EX B&S 24 (CE), SMI I924EX B&S 24 (CE), SNP I924RX MS B&S 24 (CE), and SMI I924E B&S 24. These models are particularly noted for their robust build and practical features that cater to both residential and commercial mowing needs.

The Snapper SNP I924E B&S 24 (CE) boasts a powerful Briggs & Stratton engine and delivers commendable performance with its cutting-edge technology. This model is designed with an ergonomic handle for comfort, and its lightweight construction allows for easy maneuverability. Featuring a 24-inch cutting deck, it enables swift and efficient lawn care, minimizing the time spent mowing while providing a clean, even cut.

The SNP I924EX B&S 24 (CE) takes performance a step further with enhanced features, including a better air filtration system that promotes engine longevity and efficiency. Its adjustable cutting heights provide the versatility required for various lawn conditions, ensuring a tailored cut across different grass types.

On the other hand, the SMI I924EX B&S 24 (CE) is known for its innovative technology that enhances user engagement and operational efficiency. This model integrates smart controls which allow the operator to monitor fuel levels and engine performance easily. Additionally, the model includes a maintenance monitoring system that alerts users when service is due, thus ensuring optimal functionality.

For more demanding applications, the SNP I924RX MS B&S 24 (CE) offers a robust solution with its self-propelling feature. This model is engineered for ease of use, reducing the physical strain on the operator while maintaining a high-quality cut. Its durable construction is suited for tough terrains and frequent use, presenting itself as an ideal choice for professional landscapers.

Lastly, the SMI I924E B&S 24 reinforces Snapper's commitment to quality with its high-performance engine and intuitive design. With features aimed at reducing noise and emissions, this model is aligned with environmental standards.

Each of these Snapper models represents a consistent dedication to innovation, user-friendly features, and high performance, making them exemplary choices for anyone looking to maintain a pristine garden or lawn with ease.