Snapper SMI I924E B&S 24, SMI I924EX B&S 24 (CE) manual Adjustments, Run-In Adjustment, 10.95cm

Page 27

Run-In Adjustment

ALL MODELS

1.After 5 hours of use, check for proper adjustment. Readjust clutch cable if necessary by increasing tension on cable. A small amount of arm movement is permissible if unit passes operating checks described in the Warning above.

WARNING

Gasoline is highly flammable and must be handled with care. Drain gasoline outdoors. Never drain the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills.

2.Remove the gas from the gas tank.

3.Disconnect the spark plug wire.

4.Stand snowthrower on the front of the auger housing (C, Figure 22).

5.Remove the capscrews (A) on each side of the bottom panel (B).

6.Remove the bottom panel (B).

A

A

C

B

Adjustments

8.Note the position of the friction wheel (A, Figure 24). The correct distance from the right side of the friction wheel to the outside of the frame is 4-5/16” (10.95 cm). If the friction wheel is not in the correct position, adjust as follows.

9.Move the friction wheel (A, Figure 24) to the correct distance, 4-5/16” (10.95 cm).

10.Tighten the 1/4-20 shift lever nuts (B, Figure 23) to 60 lb-in. (6,8 Nm).

11.Check that the snowthrower operates in R1. If not follow procedures 1-10 and readjust as necessary.

12.Install the bottom panel (B, Figure 22) and tighten the capscrews (A).

A

B

4-5/16”

(10.95cm)

Figure 24. Friction Disc Measurement

A.Friction Wheel

B.Frame

Figure 22. Bottom Cover

A.Capscrews

B.Bottom Panel

C.Auger Housing

7.Loosen shift lever screws (A, Figure 23), and position the shift speed lever in the lowest forward speed.

A

B

Figure 23. Shift Lever Adjustment

A.Shift Lever

B.Nuts, 1/4-20

Adjustments/Service

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Manual Part No Mfg. No DescriptionSafety Decals Safety IconsRead the Manual Table of Contents Safety Rules & Information Operating Safety Read the ManualChildren Thrown Objects Fuel and MaintenanceSafety Rules and Information Moving PartsTraining Safety Rules & InformationSafety Rules and Information Decals DecalsNorth American Model Decals Part No SMI/SNAPPER Speed Control Decal, All Models DecalsALL Model Decals CE Model DecalsSafety Icons Safety IconsNorth American / CE Models CE Models Only Identification NumbersProduct Identification Numbers CE Identification TAG MarkingsAuger Control Features & ControlsControl Locations Speed SelectorFeatures & Controls Checks Before Each START-UP OperationStarting Controls Electric StartManual Start Starting the Engine OperationEngine Speed Stopping the EngineOperating the Snowthrower Ground Speed SelectorTraction Drive Lock When Pushing the SnowthrowerDeflector Scraper BAR & Skid ShoesClearing a Clogged Discharge Chute After Each USEStorage Auger Gear Case Lubrication Regular MaintenanceMaintenance Schedule Checking Tire PressureLubrication Regular MaintenanceLubricating the Auger Shaft Assembly Check / Lubricate LinkageLubricate as shown in figure Maintenance Troubleshooting TroubleshootingPoor traction Auger does not stop when augerAuger rotates, but snow is not Thrown far enoughInitial Adjustment AdjustmentsAuger Drive Adjustment Traction Drive AdjustmentAdjustments Run-In Adjustment10.95cm Belt Adjustment Auger Drive BeltTraction Drive Belt Shear PIN Replacement Belt Guide Adjustment3.18mm Belt Replacement ServiceRotator Shaft Removal Pin, Hair Traction Drive Belt Traction Belt Change Swing Plate Alignment Tabs Service Chassis SpecificationsDimensions EngineSpecifications Replacement Parts Maintenance ItemsTechnical Manuals O D U C T S

SMI I924RX MS B&S 24 (CE), SMI I924E B&S 24, SNP I924RX MS B&S 24 (CE), SMI I924EX B&S 24 (CE), SNP I924EX B&S 24 (CE) specifications

Snapper has established itself as a leading name in the lawn care and outdoor equipment industry, offering a range of advanced and reliable products designed for efficiency and longevity. Within this offering, several models stand out: the Snapper SNP I924E B&S 24 (CE), SNP I924EX B&S 24 (CE), SMI I924EX B&S 24 (CE), SNP I924RX MS B&S 24 (CE), and SMI I924E B&S 24. These models are particularly noted for their robust build and practical features that cater to both residential and commercial mowing needs.

The Snapper SNP I924E B&S 24 (CE) boasts a powerful Briggs & Stratton engine and delivers commendable performance with its cutting-edge technology. This model is designed with an ergonomic handle for comfort, and its lightweight construction allows for easy maneuverability. Featuring a 24-inch cutting deck, it enables swift and efficient lawn care, minimizing the time spent mowing while providing a clean, even cut.

The SNP I924EX B&S 24 (CE) takes performance a step further with enhanced features, including a better air filtration system that promotes engine longevity and efficiency. Its adjustable cutting heights provide the versatility required for various lawn conditions, ensuring a tailored cut across different grass types.

On the other hand, the SMI I924EX B&S 24 (CE) is known for its innovative technology that enhances user engagement and operational efficiency. This model integrates smart controls which allow the operator to monitor fuel levels and engine performance easily. Additionally, the model includes a maintenance monitoring system that alerts users when service is due, thus ensuring optimal functionality.

For more demanding applications, the SNP I924RX MS B&S 24 (CE) offers a robust solution with its self-propelling feature. This model is engineered for ease of use, reducing the physical strain on the operator while maintaining a high-quality cut. Its durable construction is suited for tough terrains and frequent use, presenting itself as an ideal choice for professional landscapers.

Lastly, the SMI I924E B&S 24 reinforces Snapper's commitment to quality with its high-performance engine and intuitive design. With features aimed at reducing noise and emissions, this model is aligned with environmental standards.

Each of these Snapper models represents a consistent dedication to innovation, user-friendly features, and high performance, making them exemplary choices for anyone looking to maintain a pristine garden or lawn with ease.
Top Page Image Contents