Poulan 199434 owner manual Engine, Cleaning

Page 14

MAINTENANCE

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Changetheoilafterevery25hoursofoperationoratleastonce a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Number Snow ThrowerSafe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Tool BOX See FigInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingWhen cleaning, repairing, or inspecting, make When traction drive control lever is engagedUsing the CLEAN-OUT Tool See Fig Stopped. Disconnect the spark plug wireTo Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Maintenance Cleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Storage OtherTroubleshooting Service Notes Limited Warranty

199434 specifications

The Poulan 199434 is a robust and reliable chainsaw that caters to both professionals and home users alike. Known for its versatility, this model is especially popular among those who require an effective tool for yard maintenance, pruning, and even felling small to medium-sized trees. Its power-packed features and user-friendly design make it a standout option in the chainsaw market.

At the heart of the Poulan 199434 is a strong and efficient 42cc engine, which delivers a commendable power-to-weight ratio. This allows for quick and efficient cutting operations, whether you're trimming branches or tackling larger logs. The engine utilizes a two-cycle design, which not only enhances performance but also ensures lower emissions, making it more environmentally friendly.

One of the remarkable features of the Poulan 199434 is its easy-to-access air filter. This vital component helps maintain optimal engine performance by allowing users to conveniently clean or replace the filter. Additionally, the chainsaw comes equipped with an automatic chain oiler that delivers lubrication as needed, reducing friction and extending the life of both the chain and the bar.

The chainsaw's 18-inch bar is a perfect size for handling various cutting tasks, providing excellent reach without sacrificing control. The chain itself is designed for durability and efficiency, ensuring smooth cutting with minimal kickback. Users will also appreciate the chainsaw's lightweight build, which reduces fatigue during extended use, making it easier to handle for both novice and experienced operators.

Safety features are another priority for the Poulan 199434. The chainsaw includes a hand guard that provides protection against flying debris, as well as a chain brake that can stop the chain quickly in case of kickback. These safety mechanisms instill confidence in users, allowing them to operate the chainsaw with peace of mind.

In summary, the Poulan 199434 is a feature-rich chainsaw that balances power, efficiency, and safety. Its high-performing engine, user-friendly maintenance features, and emphasis on safety make it a practical choice for a variety of woodworking tasks. Whether you're a homeowner needing to manage your landscaping or a professional tackling routine jobs, the Poulan 199434 is an exceptional tool designed to meet your needs.
Top Page Image Contents