Poulan 183615 owner manual Before Starting the Engine, Scraper BAR, To Start Engine

Page 12

OPERATION

TO ADJUST SKID PLATES (See Fig. 19)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the rear 1/2" hex nut only, then moving skid plate to desired position.Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION (LOW GROUND CLEARANCE)

AUGER

HOUSING

SKID PLATE

1/2" HEX NUT

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 19

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 20)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

1.Check engine oil with snow thrower on level ground.

2.Remove oil fi ll cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 20)

•Fill fuel tank to bottom of tank fi ller neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30

days to assure fuel freshness.

12

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CHOKE CONTROL

THROTTLE PRIMER ENGINE OIL

 

FILL CAP /

 

DIPSTICK

SAFETY

IGNITION

KEY

 

GASOLINE

 

FILLER CAP

 

FUEL SHUT-

 

OFF VALVE

RECOIL

STARTER BUTTON

STARTER

 

HANDLE

POWER CORD PLUG

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 20

TO START ENGINE

•Be sure fuel shut-off valve is in the OPEN position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Se- rious personal injury or damage to your snow thrower could result.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Number Snow ThrowerTraining PreparationOperation Static Electricity HazardMaintenance and Storage API-SF-SJService and Adjustments Parts Packed Separately in Carton14-15 16-18Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Install Weight BAG See FigCheck Tire Pressure Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingPower Steering Operation See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Before Starting the Engine Scraper BARTo Start Engine Snow Throwing Tips Before StoppingIf Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Page KEY Part Description Page 183334 Knob, Lever Repair Parts Snow Thrower Model Number PP1130ESA Handles Repair Parts Snow Thrower Model Number PP1130ESA Handles Repair Parts Snow Thrower Model Number PP1130ESA Drive Washer, Flat 11 6 3452 KEY Part Description Page KEY Part Description Limited Warranty

183615 specifications

The Poulan 183615 is a robust and reliable gas-powered chainsaw designed for both residential and light commercial applications. This powerful tool is particularly favored by homeowners and professionals alike for its exceptional performance, user-friendly features, and durability.

One of the standout features of the Poulan 183615 is its powerful engine. The chainsaw is equipped with a 18-inch cutting bar and a 40cc engine, offering adequate power to tackle various cutting tasks, whether it's trimming branches, felling small trees, or performing firewood preparation. The engine is designed for easy starting, allowing users to get to work quickly without the frustration of difficult starts.

The advanced cutting technology incorporated in the Poulan 183615 includes an automatic oil pump. This feature ensures that the chain and bar are adequately lubricated during operation, reducing wear and tear and enhancing the overall lifespan of the tool. Users can also adjust the oil flow to suit the cutting conditions, making it versatile across different tasks and types of wood.

Another key characteristic of the Poulan 183615 is its lightweight design. Weighing in at just around 10 pounds, the chainsaw is easy to handle for extended periods, reducing user fatigue. The comfortable grip and well-placed controls contribute to its ergonomic build, allowing for precise handling and improved safety during operation.

Safety features are also paramount in the design of the Poulan 183615. It includes a chain brake that stops the chain’s movement quickly in the event of a kickback, enhancing user safety. The chainsaw also features a low-vibration system that minimizes vibrations felt during use, allowing for greater control and comfort.

In summary, the Poulan 183615 is designed with usability and performance in mind. With its powerful engine, ease of use, safety features, and ergonomic design, it is an excellent choice for anyone looking for a reliable chainsaw that can handle a variety of tasks. Whether you're a seasoned professional or a weekend warrior, the Poulan 183615 could be the tool you need to make your cutting tasks smoother and more efficient.
Top Page Image Contents