Poulan 183615 Assembly / PRE-OPERATION, Remove Snow Thrower from Carton, Unfold Upper Handle

Page 5

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut down all four corners of carton and lay panels fl at.

3.Remove all packing materials except plastic tie holding speed control rod to lower handle.

4.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 11)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

SPEED CONTROL ROD

RETAINER

SPRING

SPEEDSPEED

CONTROL CONTROL

BRACKET LEVER

FIG. 2

INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4)

The traction drive control rod has the long loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.

2.With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring.

TRACTION DRIVE

CONTROL ROD

RUBBER

SLEEVE

LOOP

OPENING

DOWN

PIVOT

BRACKET

FIG. 1

5

FIG. 3

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Snow Thrower Model NumberPreparation TrainingOperation Static Electricity HazardAPI-SF-SJ Maintenance and StorageParts Packed Separately in Carton Service and Adjustments14-15 16-18HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsInstall Weight BAG See Fig Know Your Snow Thrower OperationRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Power Steering Operation See FigTo Throw Snow See Fig To Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Page KEY Part Description Page 183334 Knob, Lever Repair Parts Snow Thrower Model Number PP1130ESA Handles Repair Parts Snow Thrower Model Number PP1130ESA Handles Repair Parts Snow Thrower Model Number PP1130ESA Drive Washer, Flat 11 6 3452 KEY Part Description Page KEY Part Description Limited Warranty

183615 specifications

The Poulan 183615 is a robust and reliable gas-powered chainsaw designed for both residential and light commercial applications. This powerful tool is particularly favored by homeowners and professionals alike for its exceptional performance, user-friendly features, and durability.

One of the standout features of the Poulan 183615 is its powerful engine. The chainsaw is equipped with a 18-inch cutting bar and a 40cc engine, offering adequate power to tackle various cutting tasks, whether it's trimming branches, felling small trees, or performing firewood preparation. The engine is designed for easy starting, allowing users to get to work quickly without the frustration of difficult starts.

The advanced cutting technology incorporated in the Poulan 183615 includes an automatic oil pump. This feature ensures that the chain and bar are adequately lubricated during operation, reducing wear and tear and enhancing the overall lifespan of the tool. Users can also adjust the oil flow to suit the cutting conditions, making it versatile across different tasks and types of wood.

Another key characteristic of the Poulan 183615 is its lightweight design. Weighing in at just around 10 pounds, the chainsaw is easy to handle for extended periods, reducing user fatigue. The comfortable grip and well-placed controls contribute to its ergonomic build, allowing for precise handling and improved safety during operation.

Safety features are also paramount in the design of the Poulan 183615. It includes a chain brake that stops the chain’s movement quickly in the event of a kickback, enhancing user safety. The chainsaw also features a low-vibration system that minimizes vibrations felt during use, allowing for greater control and comfort.

In summary, the Poulan 183615 is designed with usability and performance in mind. With its powerful engine, ease of use, safety features, and ergonomic design, it is an excellent choice for anyone looking for a reliable chainsaw that can handle a variety of tasks. Whether you're a seasoned professional or a weekend warrior, the Poulan 183615 could be the tool you need to make your cutting tasks smoother and more efficient.
Top Page Image Contents