Stanley Black & Decker 45SS, 36SS, 30SS Problem Possible Causes Solution, Electric starter

Page 29

 

 

 

Troubleshooting

30SS, 36SS, 45SS

 

 

 

 

Problem

Possible Causes

Solution

 

 

 

 

 

Engine will not start

1.

Key in the OFF position

1.

Turn key to ON position

 

 

2.

Insufficient fuel in the tank

2.

Add gasoline

 

 

3.

Air bubble in the fuel line

3.

Prime engine or shake bubble out

 

 

4.

Fuel valve in OFF position

4.

Turn valve ON

 

 

5.

Choke not ON

5.

Turn choke ON

 

 

6.

Choke linkage out of adjustment

6.

Refer to Engine Owner’s Manual

 

 

7.

Loose spark plug wire

7.

Add engine oil

 

 

8.

Fouled spark plug

8.

Tighten wire or connections

 

 

9.

Plugged or dirty air filter

9.

Clean or replace the plug

 

 

10.

Bad gasoline

10.

Clean or replace the air filter

 

 

 

 

11.

Drain and replace with fresh gasoline

 

 

 

 

 

Fuel is leaking from the

1.

Primer button was pressed too many

1.

Do not press primer more than 3 times. Wipe off

engine.

 

times.

 

excess fuel and allow to dry COMPLETELY before

 

 

 

 

 

attempting to start

 

 

2.

Fuel hose has become dis-connected

2.

Re-connect fuel hose and clamp(s)

 

 

3.

Carburetor has contaminants in it

3.

Fuel tank and carburetor needs to be flushed and

 

 

 

causing the bowl to flood.

 

carburetor needs cleaning.

 

 

 

 

 

Engine will not start with

1.

Not using proper gauge cord

1.

Use 120V 16 gauge cord in good condition.

electric starter

2.

Safety key is loose

2.

Verify the safety key is fully inserted.

 

 

 

 

 

Engine will not keep

1.

Water in the fuel

1.

Drain and replace with fresh fuel

running/quits

2.

Fuel valve is OFF

2.

Turn fuel valve ON

 

 

3.

Low engine oil

3.

Add engine oil

 

 

 

 

 

Augers do not turn

1.

Shear pins holding the augers may

2.

If the pins sheared, replace them as needed after

 

 

 

have sheared.

 

applying lubricant into the shaft. Call GXi Parts &

 

 

 

 

 

Service at 1-919-550-3221 or email:

 

 

 

 

 

customerservice@gxioutdoorpower.com for parts.

 

 

 

 

Shaft is not turning

1.

Shear-Pins holding the augers may

If the pins sheared, replace them as needed after

 

 

 

have sheared.

applying lubricant into the shaft.

 

 

2.

Check the gearbox.

Call GXi Parts & Service at 1-919-550-3221or email:

 

 

 

 

customerservice@gxioutdoorpower.com for parts.

 

 

 

 

 

Snow blower always pulls

1.

Skid shoes and / or scrapper blade

1.

Adjust skid shoes and / or scrapper blade so the

to one side

 

dragging more on one side than the

 

scrapper blade drags uniformly on the surface

 

 

 

other

 

being blown.

 

 

 

 

 

 

 

Rev: 12/21/2011

24

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Do not Return this Snow Blower to Store Remain with the snow blower if resold 30SS, 36SS, 45SSZero-Turn Commercial Mowers Brush MowerCommercial Walk Behind Mowers Tow Behind MowerElectric Pressure Washer Generator Cord AccessoriesContents Safety Information and Warnings Gasoline and other fuels-Safety Precautions Preparation Safety PrecautionsPreparation-Safety Precautions Equipment Operation-Safety Precautions Operation Safety PrecautionsShut the Engine OFF Clearing a Clogged Chute-Safety PrecautionsSafety Decal Identification Safety DecalsModels Feature Product SpecificationsControl Panel Control Panel and Snow Blower ComponentsDischarge Chute Direction Snow Blower Component IdentificationComments Please indicate the part that you are missingControl Panel Handles Assembly InstructionsDirectional Discharge Chute Chute CrankChute Rotation Cable Connection Chute Direction Control Cable Support Augers/Impeller Control Drive ControlSkid Shoes Drift Cutters if desiredHeadlight Filling Oil and GasolineStarting the Engine Starting the Engine Using the Recoil StartTransmission Control Operating InstructionsEngage Transmission Drive To Stop EngineClean Out Tool Never use your hands to clean a clogged chute or openingChute Direction Control HeadlightsStanley Snow Blower uses a live axle which means Using your Stanley Snow BlowerGeneral Maintenance Cleaning the Snow blower ProcedureTime Interval Break-in First 5 hrs Daily Weekly Bi-weekly MonthlyAdjusting Augers/Impeller Cable Service AdjustmentsAdjusting Drive Cable Adjusting Shift RodCheck & Replacing the Transmission Drive Belt Changing Friction Wheel Adjusting Discharge DeflectorIf the friction wheel needs to be replaced for any reason Part# B05311Extended Storage Storage InstructionsShort Term Storage Electric starter Problem Possible Causes SolutionTroubleshooting OEM Replacement Parts Replacement PartsCollector Housing Assembly Reference Parts DiagramParts Diagram To Qualify for this Warranty Limited Warranty & Service

45SS, 30SS, 36SS specifications

Stanley Black & Decker is synonymous with innovation in the tool industry, and their 36SS, 30SS, and 45SS models exemplify this commitment to excellence. These products are engineered to meet both professional and DIY needs, with a robust set of features, advanced technologies, and user-friendly characteristics.

The 36SS model stands out with its powerful motor, designed to handle even the toughest tasks with ease. This tool features a high-efficiency motor that provides a higher output while consuming less energy, making it both effective and eco-friendly. The ergonomic design allows for comfortable handling over extended periods, reducing user fatigue. It also features a variable speed control that allows users to adjust the speed according to the task at hand, providing versatility in application.

Moving on to the 30SS, this model offers compactness without sacrificing performance. It is particularly popular for its lightweight design, making it an ideal choice for users who need portability without compromising on power. The 30SS is equipped with advanced technology that includes an integrated battery management system, ensuring longer run times and optimal battery life. Its durability is enhanced by a rugged exterior that withstands harsh job site conditions, adding to its reliability.

The 45SS takes functionality to the next level by incorporating smart technology. This model features Bluetooth connectivity, allowing it to pair with mobile devices for real-time monitoring and performance tracking. Users can access data such as battery usage, maintenance reminders, and even customizable settings straight from their smartphones. Additionally, the 45SS showcases a user-friendly interface with intuitive controls, making it accessible for users of all skill levels.

All three models, the 36SS, 30SS, and 45SS, are characterized by their commitment to safety. Each tool is equipped with multiple safety features such as overload protection, anti-vibration systems, and enhanced grip designs to prevent slippage during use.

Stanley Black & Decker's focus on durability, performance, and user experience makes the 36SS, 30SS, and 45SS tools exemplary choices for both professionals and DIY enthusiasts. These models represent a perfect blend of power, innovation, and practicality, ensuring that users can tackle any project with confidence.
Top Page Image Contents