Troy-Bilt 772C0781 warranty Off-Season Storage, Wipe equipment with an oiled rag to prevent rust

Page 20

7

Off-Season

Storage

WARNING

Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance.

Drain fuel into an approved container outdoors, away from any open flame. Be certain engine is cool. Do not smoke. Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

Do not drain carburetor if using fuel stabilizer. Never use engine or carburetor cleaning products in the fuel tank or permanent damage may occur.

Observe the following, when preparing your snow thrower for off-season storage:

Drain fuel into an approved container outdoors, away from any open flame. Allow engine to cool. Extinguish cigarettes, cigars, pipes and other sources of ignition prior to draining fuel. Fuel left in engine during warm weather deteriorates and will cause serious starting problems.

If unit is to be stored over 30 days, prepare for storage as instructed in the separate engine manual packed with your unit.

Run engine until fuel tank is empty and engine stops due to lack of fuel.

Remove gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of engine.

Drain carburetor by pressing upward on bowl drain, located below the carburetor cover.

Fuel stabilizers, such as STA-BIL®, are an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Do not drain carburetor if using a fuel stabilizer.

Wipe equipment with an oiled rag to prevent rust.

Remove spark plug and pour one ounce of engine oil through spark plug hole into cylinder. Cover spark plug hole with rag. Crank engine several times to distribute oil. Replace spark plug.

Follow the lubrication recommendations found in the Maintenance Section.

Always store the snow thrower in a clean, dry area.

20

Image 20
Contents OPERATOR’S Manual 772C0781 2005Table of Contents Chute Clean-out Tool Your Responsibility Restrict the useSafe Operation Operation Do not modify engineSetting Up Your Snow Thrower RecommendationsPivoting handle upward Lower handlePrior to operating Test onInstructions care Shear Pin Storage optionalDrift Cutters If Equipped All modelsClean-Out Tool Clean-Out ToolSkid Shoes Tire Pressure Pneumatic TiresOperating Your Snow Thrower Auger Control Drive Control/ Auger Control LockFour-Way Chute Control Wheel Steering ControlsElectric Starter If Equipped Starting The EngineElectric Starter Recoil StarterRecoil Starter Auger Control TestDrive Control & Shift Lever Shift CableChute Control Standard Skid Shoe Reversible Skid ShoeShave Plate and Skid Shoes Maintaining Your Snow ThrowerLubrication Auger Belt Replacement Drive Belt Replacement Maintenance or adjustments on your machineAugers Always stop engine, disconnect sparkFriction Wheel Removal Off-Season Storage Wipe equipment with an oiled rag to prevent rustTrouble Shooting TWO Year Supreme Warranty

772C0781 specifications

The Troy-Bilt 772C0781 is a robust and versatile push lawn mower designed to meet the demands of homeowners seeking an efficient lawn care solution. This model combines power, precision, and ease of use, making it a favorite among gardening enthusiasts.

One of the standout features of the Troy-Bilt 772C0781 is its powerful engine. Equipped with a reliable Briggs & Stratton engine, it provides the necessary torque and performance to tackle various lawn conditions. The engine’s dependable performance ensures that the mower can efficiently handle both thick grass and uneven terrain, granting users the ability to maintain their lawns with ease.

The cutting deck on the Troy-Bilt 772C0781 is designed for optimal performance. With a 21-inch steel cutting deck, this mower provides a wide cutting path, allowing users to cover more ground in fewer passes. Additionally, the deck features a versatile three-in-one cutting system, enabling users to choose between mulching, rear bagging, or side discharge options. This versatility empowers homeowners to adapt to different lawn care needs throughout the seasons.

User comfort and control are significantly enhanced by the adjustable height feature. The mower allows for six different cutting height positions, ranging from 1.25 inches to 3.75 inches. This customization helps users achieve the desired look for their lawns while promoting healthy grass growth. Furthermore, the ergonomic handle design is equipped with cushioned grips, reducing fatigue during extended mowing sessions and enhancing the overall mowing experience.

Another impressive aspect of the Troy-Bilt 772C0781 is its ease of maintenance. The mower features an easy-to-access oil fill and a simple blade height adjustment mechanism, making routine upkeep straightforward for users. This focus on user-friendly design extends to its overall construction, with a durable steel frame designed to withstand the rigors of regular lawn maintenance.

In conclusion, the Troy-Bilt 772C0781 stands out as a powerful and versatile lawn mower equipped with essential features and technologies designed for user convenience. Whether tackling a small yard or a more substantial lawn, this mower provides the performance, comfort, and customization that every homeowner looks for, ensuring a well-manicured lawn all season long.